Xerox WORKCENTRE C2424 Talimatlar Kılavuzu - Sayfa 3

Yazıcı Xerox WORKCENTRE C2424 için çevrimiçi göz atın veya pdf Talimatlar Kılavuzu indirin. Xerox WORKCENTRE C2424 6 sayfaları. Copier-printer
Ayrıca Xerox WORKCENTRE C2424 için: Hızlı Referans Kılavuzu (14 sayfalar), Broşür (8 sayfalar), Tamamlayıcı Kılavuz (7 sayfalar), Teknik Özellikler (6 sayfalar), Kullanıcı Kılavuzu (43 sayfalar), Başlangıç Kılavuzu (26 sayfalar), Kullanıcı Kılavuzu (21 sayfalar), Kullanıcı Kılavuzu (20 sayfalar), Bakım Kılavuzu (20 sayfalar), Kullanıcı Kılavuzu (19 sayfalar), Talimatlar Kılavuzu (16 sayfalar), Manuel (12 sayfalar), Kurulum Kılavuzu (4 sayfalar), Kurulum Kılavuzu (2 sayfalar), Besleme Silindiri Kitinin Değiştirilmesi (2 sayfalar), Kurulum Kılavuzu (2 sayfalar), Gönüllü Ürün Erişilebilirlik Şablonu (10 sayfalar), Rekabetçi Karşılaştırma (3 sayfalar), Hızlı Referans Kılavuzu (14 sayfalar), Servis Kılavuzu (11 sayfalar), Hızlı Referans Kılavuzu (13 sayfalar)

Sayfayı Yazdır
Xerox WORKCENTRE C2424 Talimatlar Kılavuzu
Follow all warnings and instructions marked on, or supplied with, the system, options and
■
supplies.
Caution
Use of other than Genuine Xerox WorkCentre C2424 Solid Ink may affect print and copy
quality and system reliability. It is the only ink designed and manufactured under strict
quality controls by Xerox for specific use with this system. The Xerox Warranty, Service
Agreements, and Total Satisfaction Guarantee do not cover damage, malfunction, or
degradation of performance caused by use of non-Xerox supplies or consumables, or the
use of Xerox supplies not specified for this system.
Note
The Total Satisfaction Guarantee is available in the United States and Canada.
Coverage may vary outside these areas; please contact your local representative for
details.
System Location
■
Place the system in a dust-free area within a temperature range of 50 degrees F to
90 degrees F (10 degrees C to 32 degrees C) and a relative humidity range of 10 percent to
80 percent.
Place the system in an area where there is adequate space for ventilation, operation, and
■
servicing. The recommended minimal spacing is:
■
30 cm (11.8 in.) above, measuring from the top of the document feeder
■
24 cm (9.5 in.) behind
■
10 cm (3.9 in.) on the left side of the system
■
37 cm (14.6 in.) on the right side of the system, to allow access to the maintenance
unit and waste tray.
Do not block or cover the slots and openings on the system. The system may overheat
■
without adequate ventilation.
■
For optimum performance, use the system at elevations below 2,438 m (8,000 ft.).
■
Do not place the system on a carpeted location such as a carpeted floor. Airborne carpet
fibers can be pulled into the system and cause print- and copy-quality problems.
■
Do not place the system near a heat source.
■
Do not place the system in direct sunlight.
■
Do not place the system in line with the cold air flow from an air conditioning system.
■
Place the system on a level, solid non-vibrating surface with adequate strength for the
weight of the system. It should be within 2 degrees of horizontal with all four feet in solid
contact with the surface. The base system weight without any packaging materials is
approximately 42 kg (93 lbs.).
WorkCentre® C2424 Copier-Printer
A-3