Directed XpressKit DBALL Manuel - Sayfa 10
Kilitler tarafından Directed XpressKit DBALL için çevrimiçi göz atın veya pdf Manuel indirin. Directed XpressKit DBALL 19 sayfaları. Ford5 remote start ready (rsr) installation
Ayrıca Directed XpressKit DBALL için: Kurulum Kılavuzu (16 sayfalar), Manuel (14 sayfalar), Kurulum Kılavuzu (16 sayfalar)
Platform: DBALL/DBALL2
Firmware: FORD5 Remote Start Ready (RSR) Installation
Module Programming
Refer to the LED Diagnostics section on page 12 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning!
To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL.
a.
To ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b.
Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
OR
XL202 Installation
Connect XL202 to DBALL using the D2D port.
Connect the 10-pin, 12-pin and 14-pin harnesses to
1
DBALL, then wait until the LED turns ON solid red.
Note: To skip the transponder programming and use
convenience features only, press the programming button
5 times. The LED will flash orange then proceed to step 3.
Driver 's door must be opened during programming.
Open the remote. Remove the battery. Re-assemble the remote.
Hold the key up to the right side of the steering column. There will be a slot to insert the key
into or a symbol to hold it up against.
2
Note: If transponder programming was skipped, the LED turns ON solid orange for 3 seconds then shuts off
when programming is done. Press the PTS button to turn the ignition OFF. You have successfully completed
the module programming sequence with convenience features only.
Press the Push-To-Start (PTS) button to turn the ignition ON.
3
The LED flashes green.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
st
1
Go to the next page to complete the module programming.
Rev.: 20160317
SmartStart
XL202
&
rd
3
nd
2
Remove
Battery
&
ENGINE
PUSH 1X
START
STOP
Flashes Green
© 2016 Directed. All rights reserved.
Page 10
Solid