Blade Blade 180QX HD Kullanım Kılavuzu - Sayfa 15

Quadcopterler Blade Blade 180QX HD için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Blade Blade 180QX HD 20 sayfaları.
Ayrıca Blade Blade 180QX HD için: Kullanım Kılavuzu (20 sayfalar)

Sayfayı Yazdır

Stability Mode Calibration

1. Ensure all trims are centered.

2. Power on the transmitter and move the throttle stick to full throttle.

3. Ensure the transmitter is in Stability High or Low Angle Mode.

4. Hold full up elevator.

5. Connect the fully charged ﬂ ight battery in the quadcopter.

6. Both LEDs will ﬂ ash red twice, then blue twice for a few seconds.

7. When the LED turns solid blue, lower the throttle and return the elevator to center.

8. Raise the throttle to bring the quadcopter to a hover.

9. Use the trims on the transmitter to eliminate any drifting, allowing for a stable hover.

10. While in a stable hover, press and hold the camera trigger on the transmitter for 5 seconds. The quadcopter is now

calibrating input from the sensors and transmitter.

11. Release the camera trigger and land the quadcopter. Upon landing, the LEDs should ﬂ ash red then blue. When the

LEDs repeat with one blink per color, the calibration is complete.

12. If only the red LED is ﬂ ashing, the calibration has failed. Repeat the process.

13. Disconnect the battery, then return the trims to center.

Troubleshooting Guide

Problem

Quadcopter control response is

inconsistent or requires extra trim

to neutralize movement.

Quadcopter will not respond to

throttle.

Quadcopter does not function

and smells burnt after connecting

the ﬂ ight battery.

Quadcopter has reduced ﬂ ight

time or is underpowered.

LED on receiver ﬂ ashes rapidly

and aircraft will not respond to

transmitter (during binding).

Possible Cause

Aircraft not initialized on a level surface.

Battery not correctly placed in

battery slot.

Throttle too high and/or throttle trim is

too high.

Quadcopter moved during initialization.

Throttle channel is reversed.

Flight battery connected with the wrong

polarity.

Flight battery charge is low.

Inadequate power to ﬂ ight battery charger.

Flight battery is damaged.

Flight conditions might be too cold.

Transmitter too near aircraft during bind-

ing process.

Bind switch or button was not held while

transmitter was powered on.

Aircraft or transmitter is too close to large

metal object, wireless source or another

transmitter.

Full up elevator

Solution

Disconnect the ﬂ ight battery, center the control

trim and re-initialize the quadcopter.

Adjust battery position so quadcopter balances

in the center of the frame.

Reset controls with the throttle stick

and throttle trim at the lowest setting.

Disconnect the flight battery and re-initialize

the quadcopter while keeping the quadcopter

from moving.

Disconnect ﬂ ight battery, reverse the throttle

channel on the transmitter,

recconnect ﬂ ight battery.

Replace the 5-in-1 board. Connect the ﬂ ight

battery noting proper polarity.

Completely recharge the ﬂ ight battery.

Use a different USB power source for the

charger.

Replace the ﬂ ight battery and follow the ﬂ ight

battery instructions.

Make sure the battery is warm (room tempera-

ture) before use.

Power off the transmitter. Move the transmitter

a larger distance from the aircraft. Disconnect

and reconnect the ﬂ ight battery to the aircraft.

Follow the binding instructions.

Power off transmitter and repeat bind process.

Move aircraft and transmitter to another

location and attempt binding again.