ArtFoxLighting 132W 2R Kullanıcı Kılavuzu - Sayfa 2

Aydınlatma Ekipmanları ArtFoxLighting 132W 2R için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. ArtFoxLighting 132W 2R 8 sayfaları. Beam moving head yodn lamp

Sayfayı Yazdır

TECHNICAL DATA

POWER SUPPLIES

Input Voltage: AC100-240V 50-60Hz

Power Consumption: 300W

LAMP SOURCE

Professional Stage Light Lamp Source

- Type: YODN MSD132R2

- Lamp Wattage: 132W

- Lumen Output: 5,100 Lm

- Colour temperature: 8,000K±300K

- Average Lamp Life: 6000 hrs

COLOR SYSTEM

color wheel with 13 colors + open

EFFECTS SECTION

gobo wheel with 14 xed gobos + open

Electronic Focus

High speed shake effect

3-facet rotating prism

Mechanical shutter and adjustable speed strobe effect

Mechanical dimmer

CONTROL AND PROGRAMMING

Max 13 DMX 512 control channels

DMX protocol signal: USITT DMX 512

Display: LCD Display

Pan/Tilt Resolution: 16 bit

DMX signal connection: 3 pole XLR input and output

BODY

Aluminium structure with die-cast plastic cover.

Two side handles for transportation.

Device locking PAN and TILT mechanisms for transportation and maintenance.

MOVING BODY

Travel: PAN = 540° TILT = 270°

CONTROL MODE

DMX512/Master-slave/Auto

COOLING SYSTEM

Convective Fan Inside

NET WEIGHT

11 Kg

GROSS WEIGHT

13Kg

Packing Size

39 x 40 x 52 (cm)

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton check there is no transportation damage

before using the projector. Should there be any damage caused by transportation, consult your

dealer and do not use the apparatus.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain

and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other

liquids.

DO NOT mount the projector directly onto inammable surface

The projector is only intended for installation, operation and maintenance by qualied personnel.

The projector must be installed in a location with adequate ventilation, at least 50cm from

adjacent wall surfaces. Be sure that no ventilation slots are blocked.

Do not project the beam onto inammable surfaces, minimum distance is 5m

Avoid direct exposure to the light from the lamp. The light is harmful to the eye. Do not attempt to

dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualied personnel.

Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector. It is essential that each projector is correctly earthed and that

electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the

power-cord come into contact with other cables. Only handle the power-cord by the plug. Never

pull out the plug by tugging the power-cord.

Keep a projector's optical system clean. Do not touch LED lens with bare hands.

The projector should always be installed with a secondary safety xing. A safety cord is supplied for

this; it should be attached as shown in "installing the projector" section.

Shields and lens shall be changed if they have become visibly damaged to such an extent than

their effectiveness is impaired, for example by cracks or deep scratches.

LED lamps should be replaced if damaged or having reached life limit.

Exterior surface temperatures of the luminaire after 5 minutes operation is 55℃, when steady state

is achieved 70℃,

There is no user serviceable parts inside the projector, do not open the housing and never operate

the projector with the covers removed.

If you have any questions, don't hesitate to consult your dealer or manufacturer.