ArtFoxLighting 132W 2R Kullanıcı Kılavuzu - Sayfa 3

Aydınlatma Ekipmanları ArtFoxLighting 132W 2R için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. ArtFoxLighting 132W 2R 8 sayfaları. Beam moving head yodn lamp

Sayfayı Yazdır
Mode/Channel
FUNCTION
Short
Standard
Extended
mode
mode
mode
RotGobo
6
7
9
Wheel
7
8
10
Prism
8
9
11
Prism Rotation
9
10
12
Focus
Function
"Stay in a certain
10
11
13
value for more
than 5 seconds"
VALUE
DESCRIPTION
126~131
Shake from slow to fast : Gobo 7
132~137
Shake from slow to fast : Gobo 8
138~143
Shake from slow to fast : Gobo 9
144~149
Shake from slow to fast : Gobo 10
150~155
Shake from slow to fast : Gobo 11
156~161
Shake from slow to fast : Gobo 12
162~167
Shake from slow to fast : Gobo 13
168~173
Shake from slow to fast : Gobo 14
174~214
Rotation from fast to slow
215~255
Rotation from slow to fast
Prism Excluded
0~127
Prism Inserted
128~255
0~127
Position Indel 0 - 540 Angle Degree
128~190
Rotation from fast to slow
191~192
Stop
193~255
Rotation from slow to fast
0~255
0% - 100%
Unused
0~24
Reset: Effects
25~49
Unused
50~74
Reset: Pan Tilt
75~99
Unused
100~124
Reset: Complete
125~149
Unused
150~174
Lamp off
175~199
200~224 Unused
Lamp on
225~255
12

DMX TERMINATOR

In the Controller mode, at the last xture in the chain, the DMX output has to be connected with a
DMX terminator. This preventselectrical noise from disturbing and corrupting the DMX control
signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2
and 3, which is then plugged into the output socket on the last projector in the chain. The
connections are illustrated below.
1
DMX TERMINATOR CONNECTION
2
Connect a 120Ω (OHM) resistor
across pins 2 and 3 in an XLR plug
3
and insert into the DMX out socket on
120Ω

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector conguration can be set conveniently via press button switch and LCD display.
To browse or change its setup options, Press button ENTER to unlock panel. Menu will be displayed
on the screen, each menu has it own sub-menu. Each menu has specic function, Please refer to
"Operation Menu" for details.
Press button UP or DOWN if you want to browse or change through the various Setup Options.
Press button ENTER to save your settings or enter the next menu.
Press button UP or DOWN to change values.(Add or subtract)
Press button FUNC , it will return to the upper menu one by one.
TO SET THE DMX START ADDRESS
Each projector must be given a DMX start address so that the correct projector responds to the
correct control signals. This DMX start address is the channel number from which the projector
starts to "listen" to the digital control information being sent out from the controller. The xture
have 3 DMX modes. There are simple mode, standard mode and extended mode. For example
standard mode has 11 channels, so set the No. 1 projector's address 001, No. 2 projector's address
012, No. 3 projector's address 023, No. 4 projector's address 034 and so on.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel.
Press button ENTER to display DMX address.
Press button UP or DOWN , you can set the address.
Press button ENTER to conrm, which means the projector has saved the Start Address
automatically, when powered on next time, it will display the value saved last time.
Press button UP or DOWN to change values.(Add or subtract)
Press button FUNC , it will return to the upper menu one by one.
the last unit in the chain.
PIN2
5
PIN3