dji S800 Manuel

Dronlar dji S800 için çevrimiçi göz atın veya pdf Manuel indirin. dji S800 3 sayfaları. Retractable landing gearfor spreading wings
Ayrıca dji S800 için: Kullanıcı Kılavuzu (16 sayfalar)

Sayfayı Yazdır

Retractable Landing Gear

2013.01.24 Revised

Introduction

The retractable landing gear is designed for the S800 frame in order to provide a better perspective in

aerial-filming / photography work. By using a 2-position switch channel of the R/C transmitter, you can

control the landing gear to retract remotely. The retractable landing gear will not block the view of the

camera lens, making smooth shooting in all directions possible.

Disclaimer & Warning

Thank you for purchasing this DJI product. Please regularly visit the S800 web page at

www.dji-innovations.com. This page is updated regularly. Any technical updates and manual corrections will

be available on this web page. Due to unforeseen changes or product upgrades, the information contained

in this manual is subject to change without notice.

Please strictly follow the manual to assemble and use the retractable landing gear. As DJI Innovations has

no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted

for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting

liability. DJI Innovations accepts no liability for damage(s) or injuries incurred directly or indirectly from the

use of this product.

DJI and S800 are registered trademarks of DJI Innovations. Names of product, brand, etc., appearing in this

manual are trademarks or registered trademarks of their respective owner companies. This product and

be reproduced in any form without the prior written consent or authorization of DJI Innovations. No patent

liability is assumed with respect to the use of the product or information contained herein.

for Spreading Wings S800

V 1.2

Assembly & Connection

The part with the control board attached is defined as left, the other part is right. Make sure to make a

distinction between the left and the right servos.

STEP1

Servo Installation

(If the servos have already been installed, please skip this step.)

1. Define and mark two

HS-7954SH

servos from

2. Connect the left servo to the [L] port on the control board, and the right servo to the [R] port.

3. Keep pressing the SET button with the aid of a small tool, and then power on. You will see the yellow

LED flashes quickly, and then wait until the servos have finished their position initialization.

4. Make sure the servo arm is parallel to the servo's center line (shown in the following Fig).

5. Power off, and assemble the left and right servos to the left and the right parts of the landing gear.

Tips: If you use your own servos, it is recommended to use dedicated programmer from Hitec to enlarge

the servo travel from 120° to 150°, and then install servos by the above steps. Servos from DJI have been

enlarged servo travel.

STEP2

Mechanical Assembly

1. Assemble the left and the right parts respectively, and then fix the screws at the joints with appropriate

screw thread lock.

2. Connect the left and right parts with the connecting rod.

3. For safety reasons, make sure to connect the springs to both parts.

4. Assemble the battery Bracket, referring to the "S800 User Manual".

STEP3

Electrical Connections

1. Plug the cables from the servos into the correct ports on the control board. Make sure the right servo is

connected to the [R] port, and the left servo to the [L] port.

2. Connect the required 2-position switch channel of the R/C receiver to the [IN] port.

Ser voArmInstallation

ine

Servo

CenterL

Arm

RightS

er vo

Ser vo

Finished

Right art of the anding ear

Left art of the

GimbalF

Hitec

as left servo and right servo.

Ser voAssembly

LeftS

ervo

ControlBoard

DANGER！！！

DO NOT TOUCH!

RightSer vo

LED

LeftSer vo

SETButton

ReceiverChannel

anding ear

ront

irection