Altronix HubSat42Di Kurulum Kılavuzu - Sayfa 3
Anahtar Altronix HubSat42Di için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Altronix HubSat42Di 12 sayfaları. Passive utp transceiver hub with integral isolated camera power
Ayrıca Altronix HubSat42Di için: Kurulum Kılavuzu (8 sayfalar)
Sayfayı Yazdır
Altronix HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power transmits UTP video,
RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels
in a wall mount enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with
AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners. In
addition, the unit features individually selectable 24VAC or 28VAC electronically isolated PTC protected outputs
with surge suppression. Optionally, the HubSat4Di can be used as an accessory module to transmit video from
up to 4 cameras over a single CAT-5 or higher structured cable back to the HubWay, HubWayLD or HubWayLDH
Passive and Active UTP Transceiver Hubs. In addition, the HubSat4Di provides power to these cameras locally to
eliminate the possibility of voltage drop associated with long cable runs.
Input:
• 115VAC, 50/60Hz, 1.25A.
Video:
• Four (4) channels of quality video over twisted pair
up to a distance of 750 ft. per channel.
• Four (4) 75 Ohm video outputs.
Data:
• RS422/RS485 data input.
Power:
• Individually selectable 24VAC or 28VAC power
outputs with OFF position.
• Unit provides up to 1A max. per channel not to
exceed a total of 4A maximum current.
• Individual electronically isolated outputs.
HubSat42Di
• HubSat4Di w/four (4) HubWayAv Video Balun/
Combiners for 24VAC Cameras.
WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes
in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place
the enclosure's upper keyholes over the two upper screws; level and secure. Mark the position of the lower
two holes. Remove the enclosure. Drill the lower holes and install two fasteners. Place the enclosure's
upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all
screws (Enclosure Dimensions, pg. 12). Secure green wire lead to earth ground.
2. Set illuminated master power disconnect circuit breaker to the [OFF] position (Fig. 4a, pg. 8).
3. Connect 115VAC 50/60Hz to the black and white flying leads of open frame transformer. Secure ground
wire (Green) to earth ground (Fig. 5, pg. 9). The power LEDs (Green) for Channels 1-4 of the HubSat4Di
will illuminate when AC power is present (Fig. 1e, pg. 6)
4. S elect 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4Di (Fig. 4, pg. 8) with the
corresponding output voltage switches. Select OFF position when servicing or installing individual cameras
(Fig. 1d, pg. 6).
5. Connect the BNC video outputs marked [Video 1-4] on HubSat4Di to the corresponding video inputs on
the head end equipment (DVR) (Fig. 1a, pg. 6).
6. Connect terminals marked [+ Data –] on HubSat4Di (polarity must be observed) to the RS422/RS485
output of the head end equipment (DVR) (Fig. 1f, pg. 6). When using fixed cameras disregard this step.
HubSat4Di Installation Guide
Overview:
Specifica tions:
Power (cont.):
• PTC protected outputs are rated @ 1A per channel.
• Surge suppression.
Visual Indicators:
• Four (4) power LED indicators.
Enclosure Dimensions (H x W x D):
Optional Accessories:
• Video Balun/Combiners:
Additional Models:
HubSat43Di
• HubSat4Di w/four (4) HubWayDv Video Balun/
Installation Instructions:
8.5" x 7.5" x 3.5" (215.9mm x 190.5mm x 88.9mm).
- HubWayAv - for use with 24VAC cameras.
- HubWayAv2 - for use with 24VAC cameras.
- HubWayDv - for use with 12VDC cameras.
Combiners for 12VDC Cameras.
- 3 -