Altronix HubSat42Di Kurulum Kılavuzu - Sayfa 5
Anahtar Altronix HubSat42Di için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Altronix HubSat42Di 12 sayfaları. Passive utp transceiver hub with integral isolated camera power
Ayrıca Altronix HubSat42Di için: Kurulum Kılavuzu (8 sayfalar)
Sayfayı Yazdır
2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked
[PVD1] on HubSat4Di (Fig. 1i, pg. 6). Plug the RJ45 connector at the opposite end of the CAT-5 or
higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1.
• For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner
(Figs. 2a, 2b, 2e, pg. 7).
• For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 7).
The total cable distance must not exceed 750 ft. for video transmission between the HubSat4Di and each
camera. Repeat this step for all other camera channels [PVD 2-4].
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8).
Power LEDs (Green) of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 6) and
HubWayAv, HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present
(Fig. 2b, 2d, pg. 7).
4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 7) before making connections
to each camera to ensure proper operation and avoid possible damage.
5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8).
6. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power
inputs of the cameras (Figs. 2a-2e, pg. 7). Polarity must be observed.
• HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 7).
• HubWayDv/ - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 7).
7. Connect the terminals marked [+ DATA –] of HubWayAv, HubWayAv2 or HubWayDv Video Balun/
Combiners to the data input terminals of cameras for PTZ control (Figs. 2b-2e, pg. 7). Polarity must be
observed. When using fixed cameras disregard this step.
8. Connect the BNC connector of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the
BNC video outputs of cameras (Figs. 2b-2e, pg. 7).
9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8).
10. The power LEDs (Green) of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 6).
Note: If any of the power LEDs are not illuminated the cause may be due to the following:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
c. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 6).
d. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
To reset the PTC:
1. Set the voltage output selector switch for that corresponding channel to the OFF position.
Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset
(Fig. 1d, pg. 6).
2. Eliminate the trouble condition (short circuit or overload).
3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 6).
Alternate 24VAC Fixed Camera Hookup (Fig. 7a, pg. 9).
After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay,
HubWayLD or HubWayLDH UTP Transceiver Hubs proceed with the following.
1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8).
2. Connect one end of the coaxial cable to the BNC connector marked [Video1] on HubSat4Di (Fig. 1a, pg. 6).
Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig. 6a, pg. 9).
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8).
Measure the output voltage at terminal pair marked [AUX1] on HubSat4Di to ensure proper operation and
avoid possible damage (Fig. 1c, pg. 6).
4. Connect the power output terminal pair marked [AUX1] on HubSat4Di to the power inputs of camera 1
(Fig. 1c, pg. 6). Repeat steps 1-3 for each additional camera [AUX2-4].
HubSat4Di Installation Guide
- 5 -