Alula RE114 Hızlı Başlangıç Kılavuzu - Sayfa 2

Duman Alarmı Alula RE114 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Alula RE114 12 sayfaları. Smoke alarm interlogix compatible

Sayfayı Yazdır

Normal Operation

Power Up

Standby

Sensing Fire

Fault Mode

Low Battery

Faulty Smoke Sensor

Faulty Heat Sensor

End of Life

Silence Sounding

Alarm

Silence "End of Life"

indication (up to 30

days)

Test Mode

Test Smoke Alarm

Alarm Memory

24 Hour Memory

Long Term Memory

* Pressing and holding test button for 6 beeps causes alarm to be sent.

1.1. Normal Operation

1.1.1. Power Up

Twist off the Alarm from the mounting

plate (see Quick Start Guide). Remove

the battery tab to power the Alarm, the

red LED will flash once followed by one

flash of the yellow LED to indicate that

the Alarm has been powered successfully

and is now in standby mode.

1.1.2. Standby

In standby mode there are no active

visible or audible indications which can

be intrusive to the householder. To

confirm that the Alarm is operational

perform a weekly button test.

1.1.3. Weekly Button Test

Press and hold the test button and verify

that the red LED flashes rapidly and the

Alarm ramps up to full sound. Pressing

and holding the test button for six beeps

will cause fire alarm to be sent to panel.

1.1.4. Sensing Fire

As soon as the Alarm senses smoke it will

go into Alarm. The red LED on the Alarm

sensing smoke flashes rapidly to indicate

this is the Alarm sensing smoke / fire.

Follow the instruction in section 3 and

evacuate the building.

Indicator Summary

Action

Insert Battery

Action

Press & Release

Button

Press & Release

Button

Action

Press Button*

Action

Press & Hold

Button

Red LED

1 Flash

Off

Rapid Flashing

Off

Red LED

Off

1 Flash every 48 sec

Off

2 Flashes every

48 sec

Off

2 Flashes every

48 sec

Off

3 Flashes every

48 sec

1 Flash every

Off

8 sec

Off

Off for 72 hours

Red LED

Rapid Flashing

Off

Red Led

2 Flashes every

Off

48 sec for 24

hours

Rapid Flashing

Off

1.1.5. Silence False / Nuisance alarm

Occasionally Smoke Alarms can be

activated by phenomena other than fire,

e.g. dust, insects, cooking fumes. Once

you are sure it is a nuisance alarm press

the large test button to silence the Alarm

for 10 minutes – the red LED will then

flash every 8 seconds for 10 minutes.

1.2. Fault Conditions

1.2.1. Low Battery

The Alarm will emit a short beep and

flash the Yellow LED when it becomes

partially depleted. Check the date when

the Alarm should be replaced which is

given on the sidewall of the Alarm. When

electronic self testing indicates that the

battery is becoming low the Alarm will

beep and the yellow LED will flash at

the same time (about every 48 seconds)

to warn the user. This indicates that the

battery or batteries must be replaced.

1.2.2. Contaminated Chamber

If the Alarm sounds without any apparent

smoke being present, press the test

button to silence the Alarm for 10

minutes (as described in 1.1.5 above).

If the Alarm sounds again it may be

contaminated. Pressing the test button

Yellow LED

Off

Full Sound

Yellow LED

1 Beep

2 Beeps

3 Beeps

Off for 10 mins

Off for 72 hours

Yellow LED

Full Sound

Yellow LED

Off

Rapid Chirping

Sounder