Dodge HXT405A Manuel - Sayfa 4

Otomobil Aksesuarları Dodge HXT405A için çevrimiçi göz atın veya pdf Manuel indirin. Dodge HXT405A 9 sayfaları. For hydroil, torque-arm speed reducers taper bushed for char-lynn h, s, t and 2000 series 6b spline motors

Sayfayı Yazdır
Dodge HXT405A Manuel
Table 1 – Oil Volumes
† Position A
Reducer
Fluid
Size
Ounces
Quarts
(Approx)
(Approx)
HXT305A
28
7/8
HXT405A
48
1½
3
HXT505A
108
3
† Refer to Fig. 1 on page 2 for mounting positions.
U.S. Measure: 1 quart = 32 fluid ounces = .94646 liters.
Minimum Oil Recommendations for Average Operating Conditions
Table 2 — Lubrication Recommendations —
ISO Grades for Ambient Temperatures of 15º to 60º
Output
RPM
1
2
3
4
5
301–400
220
220
150
150
150
201–300
220
220
150
150
150
151–200
220
220
150
150
150
126–150
220
220
220
150
150
101–125
220
220
220
220
150
81–100
220
220
220
220
220
41–80
220
220
220
220
220
11–40
220
220
220
220
220
1–10
220
220
220
220
220
Below – 23ºF call application engineering.
20ºF to -22ºF use Mobil SHC 627.
Above 125ºF use Mobil SHC 634.
NOTE:
Pour point of lubricant selected should be at least
10ºF lower than expected minimum ambient starting
temperature.
GUIDELINES FOR TORQUE-ARM REDUCER LONG-TERM STORAGE
During periods of long storage, or when waiting for
delivery or installation of other equipment, special
care should be taken to protect a gear reducer to have
it ready to be in the best condition when placed into
service.
By taking special precautions, problems such as
seal leakage and reducer failure due to the lack of
lubrication,
improper
contamination
can
precautions will protect gear reducers during periods
of extended storage:
Preparation
1. Drain the oil from the unit. Add a vapor phase
corrosion inhibiting oil (VCI–105 oil by Daubert
Chemical Co.) in accordance with Table 3.
2. Seal the unit air tight. Replace the vent plug with a
standard pipe plug and wire the vent to the unit.
3. Cover the shaft extension with a waxy rust
preventative compound that will keep oxygen away
from the bare metal. (Non-Rust X-110 by Daubert
Chemical Co.).
4. The instruction manuals and lubrication tags are
paper and must be kept dry. Either remove these
documents and store them inside or cover the unit
with a durable waterproof cover which can keep
moisture away.
Volume of Oil Required to Fill Reducer to Oil Level Plug
† Position B
Fluid
Liters
Ounces
(Approx)
(Approx)
(Approx)
.83
48
1.42
72
/
3.19
136
8
Reducer Size
6
7
8
9
10
12
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150 150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
220
220
220
220
220
150
220
220
220
220
220
220
lubrication
quantity,
be
avoided.
The
following
Fluid
Liters
Quarts
Ounces
(Approx)
(Approx)
1½
1.42
44
2¼
2.13
68
4¼
4.02
124
Note: If reducer position is to vary from those shown in Figure 1
either more or less oil may be required. Consult factory.
ISO Grades for Ambient Temperatures of 15º to 125º
Output
13
14
15
RPM
1
150
150
150
301–400 320 320 220 220 220 220 220 220 220 220 220 220 220 220
150
150
150
201–300 320 320 220 220 220 220 220 220 220 220 220 220 220 220
150
150
150
151–200 320 320 220 220 220 220 220 220 220 220 220 220 220 220
150
150
150
126–150 320 320 320 220 220 220 220 220 220 220 220 220 220 220
150
150
150
101–125 320 320 320 320 220 220 220 220 220 220 220 220 220 220
150
150
150
81–100
320 320 320 320 320 220 220 220 220 220 220 220 220 220
150
150
150
41–80
320 320 320 320 320 220 220 220 220 220 220 220 220 220
150
150
150
11–40
320 320 320 320 320 320 320 320 320 320 220 220 220 220
220
220
220
1–10
320 320 320 320 320 320 320 320 320 320 320 320 320 320
See page 8 for lubricant viscosity classification
equivalents.
Special lubricants may be required for food and
drug industry applications where contact with the
product being manufactured may occur. Consult a
lubrication manufacturer's representative for his
recommendation.
5. Protect the reducer from dust, moisture, and other
contaminants by storing the unit in a dry area.
6. In damp environments, the reducer should be
packed inside a moisture-proof container or an
envelope of polyethylene containing a desiccant
material. If the reducer is to be stored outdoors,
cover the entire exterior with a rust preventative.
or
When Placing the Reducer into Service
1. Assemble the vent plug into the proper hole.
2. Clean
solvents.
3. Fill the unit to the proper oil level using a
recommended lubricant. The VCI oil will not affect
the new lubricant.
4. Follow the installation instructions provided in this
manual.
Table 4—Quantities of VCI #105 Oil
Case Size
HXT305A
HXT405A
HXT505A
VCI #105 & #10 are interchangeable.
VCI #105 is more readily available.
4
† Position C
Fluid
Liters
Quarts
Ounces
(Approx)
(Approx)
(Approx)
3
1
/
1.30
44
8
1
2
/
2.01
60
8
7
3
/
3.67
120
8
Table 3 — Lubrication Recommendations —
Reducer Size
2
3
4
5
6
7
8
the
shaft
extensions
Quarts or Liters
† Position D
Liters
Quarts
(Approx)
(Approx)
3
1
/
1.30
8
7
1
/
1.77
8
3¾
3.54
9
10
12
13
14
15
with
petroleum
.1
.2
.3