AMSEC ESL15 Інструкція з експлуатації - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Замки. AMSEC ESL15. AMSEC ESL15 4 сторінки. Electronic lock
Також для AMSEC ESL15: Інструкція з експлуатації Посібник з експлуатації (10 сторінок)

Друкувати сторінку

American Security Product Co.

2.9

At any time during opening or combination changing the unit will register the first 5 digits of the

combination into the "buffer" that receives input. The 6

pressed. For example, if your press C-1-2-3-4-5-7-4-5-2-7-6-# the program recognizes only

the C-1-2-3-4-5-6-# input. The last numeric key pressed continues to replace the one prior

until the "#" key is pressed to indicate completion. This is a security feature that allows you to

baffle an on-looker that may be trying to memorize your combination. This is the electronic

equivalent to a Spy proof Dial.

Users

There are 10 User Combinations possible. The Master User (User 0) is the one and only code that

is allowed to control all the other users, their access privileges and function setting. Users 1-8 are

only active if Multi-User mode is Enabled (F10=1) and the individual User Number has been

Enabled and a combination entered for that user by the Master User.

3.1 User 0:

Designated the Master User. Has control over all Subordinate Users and setting of

all functions.

3.2 Users 1 through 8: Referred to as Subordinate Users. They only have access and privileges

as the Master User assigns them.

3.3 User 9:

Armored Car User. This is a special code used only for the purpose of bypassing

the Time Delay. This code will not open the lock, only bypass Time Delay.

Combination Changing

One of the strengths of an electronic safe lock is the quick and easy changing of the PIN code(s).

This adds to security because you can change codes at will if you suspect your combination is

known by others.

The combination change method for the Primary code (Master User) can be done two ways, with or

without a User Number. All combination changes require an authorization code and two entries of

the new combo as verification.

Note: In the event that Function 60 (Subordinate Combo Change) is set to Disable (F60=0), only

the Master Code will authorize a change. Examples and conditions:

4.1 Master User Code change:

At any time, the Master User combo can be changed by keying:

C - # - (Old Master Code) - # - (New Master Code) - # - (New Master Code) - #

4.2 Multiple User Mode Change and F60=1: Changing of any combination, including the Master

User Code, can be changed by the following sequence:

C- # - (User No.) - # - (Old User Code) - # - (New User Code) - # - (New User Code) - #

4.3 In the event Function 60 is Disabled (F60=0) or you are adding a new User, then the combo

change must be authorized with the Master User's code:

C- # - (User No.) - # - (Master Code) - # - (New User Code) - # - (New User Code) - #

Combination Change Examples

The Master Combo is 159260 and you wish to change it to 918273. Do the following:

C-#-0-#-159260-#-918273-#-918273-#

User 5's combination is 342312 and you wish to change it to 768798

C-#-5-#-342312-#-768798-#-768798-#

P/N 4305356 Revision C

digit will be the last numeric key

C-#-159260-#-918273-#-918273-#

User 5's combination is unknown and you wish to set it to 768798, the Master Combo is 159260

C-#-5-#-159260-#-768798-#-768798-#

Lock Feature Setting and Function Codes.

The ESL15's advanced features are controlled only by the Master User, and are set using Function

Codes. A function can be turned on/off or set using the Function Code with the Master User code

as authorization for changing or setting the function. A Function Code is a 2-digit code that

associates to a particular setting. Each Function Code has a default, or standard setting, which is in

the lock when there have been no changes or after a Function Reset (F99) has been executed.

They are as follows.

Function Code List

Function

Function Description

Time Delay Mode Enable/Disable

Set Time Delay Period

Set Open Period

Multiple User Mode Enable/Disable

Add/Enable a User Combo

Disable a User Combo

Disable All Users

Dual Combo Mode Enable/Disable

Enable/Disable Two Subordinate Combos Opening

Armored Car Time Delay Bypass Enable/Disable

Enable/Disable Subordinate Authorization of TDL Bypass

Subordinate User Combo Change Enable/Disable

Reset All Functions to Default settings

A function is set in the following standard format:

C - # - (2 Digit Function Code) - # - (Master User Code) - # - (Function Setting) - #

SGCT

After each "#", a Short Good Combo Tone (

pressed, at which time it sounds a Long Good Combo Tone (L

of a function. Any time during the sequence, if incorrect or invalid numbers are pressed, a Bad

Combo Tone (4 short beeps) will sound and the lock will go to rest. A function that has an on/off

condition rather than a numeric setting requires a 1 (on) or a 0 (off) as the Function Setting.

Note: If a default setting is what is desired, then the setting of that function is not necessary.

5.1 Time Delay Settings (Functions 01, 02 & 03)

5.1.1

To Enable Time Delay:

C - # - 01 - # - (Master Code) - # - 1 - #

5.1.2

To Disable Time Delay:

C - # - 01 - # - (Master Code) - # - 0 - #

3 March, 2016

American Security Product Co.

SGCT

) will be given, until the last "#" of the sequence is

SGCT

) indicating the successful setting

GCT

Enable=1, Disable=0

Setting

Default

Range

1 or 0

01 to 99

1 to 9

1 or 0

1 to 8

1 or 0

LGCT