Formax FD 8500SC Посібник оператора - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник оператора для Знищувач паперу Formax FD 8500SC. Formax FD 8500SC 2 сторінки. Paper shredders cross-cut strip-cut
Також для Formax FD 8500SC: Посібник оператора (2 сторінок)
Друкувати сторінку
Specifi cations
FD 8500CC
Cutting Style:
Cross Cut
Shred Size:
5/32" x 1-1/5"
Sheet Capacity: 16 to 18
Speed:
31 feet per minute
Feed Opening:
16"
Dimensions:
24" W x 20" D x 35" H
Bin Capacity:
26 gal.
Weight:
242 lbs.
Power supply:
110V, 50/60Hz
Cutting heads accept credit cards, staples and paper clips.
Set-up Guidelines
1. Install the shredder on a level surface, away from heat sources and
direct sunlight.
2. Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet
is shared with another electronic device, the total current should not
exceed 30A (at 110V).
Operation
1. Open the door and turn the power switch "ON." Close
door.
2. Auto Start/Auto Stop
When the "START A/M" button is pushed, the signal lamp
"AUTO" will light. Insert paper to shred. The shredder will
start and stop automatically when using this function.
3. Manual Operation
If paper is too small for the shredder's sensors to detect,
shred it manually. Push the "START A/M" button once
more and the "MANUAL" lamp will light. Insert paper to
be shredded. Three minutes after shredding, the cutter
automatically stops rotating.
FD 8500SC
Strip Cut
5/32"
20 to 22
33 feet per minute
16"
24" W x 20" D x 35" H
26 gal.
242 lbs.
110V, 50/60Hz
4. Reverse Operation
Push the "REV" button and the signal lamp "REV" will light and cutters will
operate in reverse. If too much paper is inserted at one time in standard
modes, the shredder will automatically operate in reverse. If this occurs,
remove the inserted paper and shred in smaller amounts. NOTE: The
maximum amount of paper to be shredded differs according to paper
quality, humidity and voltage. If the shredder is to be used continuously, do
not insert more than half of the maximum capacity.
5. Full Sensor
If the wastebasket is full, the "FULL" lamp will light and the cutter will stop
automatically. Open the door, empty the wastebasket of paper strips/chips,
replace the wastebasket, close door, and continue to shred.
Safety Precautions
To avoid personal injury, and damage to the shredder, observe the
following safety precautions. Please keep these instructions for future
reference.
•
Keep hands, long hair, clothing, ties, jewelry and other loose items away
from the paper entrance and shred outlet.
•
Do not use the shredder for anything other than its intended purpose.
Never use it to shred cloth, plastic, cardboard or any hard material that
will cause damage to the shredder blades.
•
Do not allow children to use the machine.
•
Do not operate with a damaged power cord or plug, or when the machine
is damaged in any manner.
•
Unplug the shredder when it is being moved, or if it is not in use for an
extended period of time.
•
Do not disconnect the power by pulling only the cord. Hold the plug when
disconnecting.
•
Keep the shredder away from direct sunlight.
•
In case of emergency, push the "STOP" button, or pull the plug out of the
wall outlet.
•
Do not sit on the shredder or place anything on top of it.
•
Never open the fi xed switch or cover.