DSC PC1000 Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Клавіатура DSC PC1000. DSC PC1000 8 сторінок.
Також для DSC PC1000: Інструкція з експлуатації (8 сторінок)

Друкувати сторінку

INTRODUCTION

Congratulations on your purchase of the DSC PC1000 Burglar Alarm Control System.

This equipment has been designed to give you the greatest possible flexibility and

convenience in the use of your security system. This booklet is intended to serve as

a handy reference and should be kept in a secure place.

Your DSC PC1000 Security System is made up of a control panel, one or more

keypads, and various detectors and sensors. The control panel will be mounted out

of the way in a utility room or basement. The metal cabinet contains the system

electronics, fuses and stand-by battery. There is normally no reason for anyone but

the installer to have access to the control panel. The keypad(s) have display lights

and command entry keys. The keypad is used to send commands to the system and

to display the current system status. Keypads are mounted in convenient areas close

to the exit-entry doors.

The security system has up to four zones or areas of

protection. Each zone used will have connected to it various sensors, such as door

or window contacts, motion detectors, glassbreak detectors and vibration or shock

sensors. When a sensor is in alarm, a keypad light will be on to indicate which zone

is in alarm. The "Ready" light on the keypad will come ON when all the detectors are

closed. The "Ready" light indicates the system is ready to arm.

IMPORTANT NOTICE

Digital Security Controls Ltd. recommends that you read this manual carefully and

become familiar with the operation of your security system. Check with the installer

to see which commands listed in this manual apply to your particular security system.

Fill out the system reference sheet and store this booklet in a secure place for future

reference. It is important to test your system every week. To do this, first inform the

monitoring station that you are testing your system. Then, with the system disarmed,

activate all detection sensors one at a time and observe the zone light come on at the

keypad as each sensor is activated.

Perform a bell test by using the [*],[4]

command. The PC 1000 can be programmed at the time of installation to automatically

perform a test transmission to the monitoring station on a regular basis. If the system

has not been programmed for this automatic test, call the monitoring station for

instructions on how to perform a test transmission.

Don't forget to inform the

monitoring station when you have finished your test.

Check to see if the "System" light is on when arming the system. The "System" light

will be on if a zone is bypassed, an alarm has occurred, or if there is a system trouble

condition. See the Trouble Display section in this manual for a description of the

different trouble conditions.

Contact your installer for assistance if the trouble

condition cannot be located and corrected.

IMPORTANT N O T E - - - - - - - - - - - -

Remember that no security system can prevent emergencies. It is only

intended to alert you in case of an emergency and should not take the

place of prudent security practices or life and property insurance.

MASTER CODE

The 4 digit Master Code is used for arming and disarming the system, for programr:ning

additional access codes, and for changing other features. The Master Code will be

supplied to you by your installer. All keypad entries are made by pressing one key

at a time, with the exception of keypad zone activation.

ARMING

They "System" light is a warning light. Determine why the "System" light is ON before

arming the system. See the System Display Light section in this manual.

To arm the system, first close all protected doors and windows and stop movement

in areas covered by motion detectors. Check to see that the "Ready" light is ON (all

zones are closed). The system cannot be armed unless the "Ready" light is ON. Enter

a [ 4 digit access code]. As each digit is entered, the keypad sounder will beep. Once

the correct access code is entered, the "Armed" light will come ON and the keypad

sounder will beep quickly. If the access code was entered incorrectly or the "Ready"

light was not ON, the keypad sounder will beep ste_adily for 2 second~. ':"'hen the

correct code is entered and the system is armed, exit through the door 1nd1cated by

your installer as the exit-entry door. At the end of the allowed exit time, all lights on

the keypad will go OFF except for the "Armed" light.

DISARMING

Enter the premises only through the door indicated by your installer as the entry door.

The keypad sounder will be ON. Go to the keypad and enter the [ 4 digit access ~ode].

an error is made entering the code, press the[#] key and enter the code again. Do

not repeatedly enter the access code without first pressing the [#] key. Once the

correct access code is entered, the "Armed" light will go OFF and the keypad sounder

will stop. The correct access code must be entered before the allowed entry time

expires.

If an alarm occurred while the panel was armed, the "System" light and the light for

the zone which caused the alarm will start to flash and will continue flashing for 2

minutes. To stop the flashing display, press the [3] key and the system will return to

the Ready state.

If you return home and find an alarm has occurred while you were away, it is possible

that an intruder may still be on the premises. Go to a neighbour's and if your system

is monitored, call the monitoring station. They will advise what action has been taken

as a result of the alarm and whether the premises are safe to enter. If your system

is not monitored, call the local police to investigate.

SYSTEM DISPLAY LIGHT

The "System" light is a warning indicator for any of the following conditions. It

indicates there is a bypassed zone; there is system trouble; or that an alarm has

occurred since the last time the system was armed. When the "System" light is ON,

press[*] [1] to check for a bypassed zone. Press[*] [2] to check for system trouble.

Press [ *] [3) to see if there was an alarm during the last armed period. See Zone

Bypassing, Trouble Display and the Alarm Memory sections in this booklet.