Auber Instruments SYL-5352P-S Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Регулятор температури Auber Instruments SYL-5352P-S. Auber Instruments SYL-5352P-S 10 сторінок. Usb ramp and soak pid temperature controller

Друкувати сторінку

AUBER INSTRUMENTS

Display mode 1: normal operating mode. When the power is turned on, the

upper display window shows the measured value (PV) and the lower window

shows the four-digit set value (SV).

Display mode 2: checking the step status. Press the DOWN arrow key once

to change the display from mode 1 to mode 2. The upper display window shows

your current reading temp, and the lower window shows the current step

segment number starting at "P". Press DOWN arrow key to go back. Then press

DOWN arrow key again to show the timer information. The upper display window

shows your current reading temp, and lower window shows the time which

current step has run starting at "F". This timer unit depends on parameter SEC

(note 5.3.16.). It can be either by minute (SEC = 0) or by second (SEC = 1).

Press DOWN arrow key again to return to the display mode 1.

Display mode 3: Ramp soak step settings. Press and hold SET key and A/M

keys together for 3 seconds to change the display from mode 1 to mode 3. This

mode is used for step program settings and step control parameters.

Display mode 4: Parameter setting mode. Press and hold the SET key for 3

seconds to enter the display mode 4. The top window shows the name of a

parameter and the bottom window shows its value. Use the UP and DOWN arrow

key the change the value; use the SET key to save the change and go to the

next parameter.

Display mode 5: Step jumping. Press and hold A/M key for 3 seconds and you

will see current reading temp on the top and current step segment number on

bottom. The decimal point on the right bottom display is flashing. Use UP and

DOWN arrow keys to change the step segment number, then press and hold

A/M key for 3 seconds to confirm and jump.

Display mode 6: Change set temp (single step mode only). For single step

mode (RUN = 0), user can change set temperature by pressing and holding UP

arrow keys for 3 seconds. Then use UP and DOWN arrow key to change its

value. Press SET key once to confirm and exit.

5. Parameter Settings

5.1. Parameter setup mode

When the display mode is 1 or 2, press SET and hold for roughly 2 seconds until

the parameter setup menu is displayed (display mode 3). Please refer to 5.3 for

how to set the parameters.

5.2. Setup flow chart

While in the parameter setup mode, use ▲ and ▼ to modify a digit and use A/M

to select the digit that needs to be adjusted. Press the A/M and SET key at the

same time to exit the parameter setup mode; otherwise, the instrument will

automatically exit if no key is pressed for 10 seconds. Figure 4 is the setup flow

chart. Please note that changed parameter will be automatically registered

without pressing the SET key. If the controller is locked (see 7.16), only limited

parameters (or no parameters) can be changed.

2020.06

5.3. List of system parameters

Table 2. System parameters.

System Parameter Menu

Press & Hold SET Key for 3s to Enter

Code

Description

Alarm 1 Setting

AL1

AL2

Alarm 2 Setting

Input offset

Proportional

Constant

Integral Time

Derivative Time

Cycle Time

FILt

Digital Filter

Hysteresis Band

Decimal Point

Position

OUTH

Output High Limit

OUTL

Output Low Limit

Auto Tuning

Configuration

LocK

Privilege

Input Sensor Type

OP-A

Display Temp Unit

Alarm Output

ALP

Definition

System Function

COOL

Selection

Display High Limit

PuH

Display Low Limit

PuL

Communication

Addr

address

Communication baud

bAud

rate

Set Temp Menu (Single Step Mode Only, RUN = 0)

Press & Hold Up Arrow Key for 3s to Enter

Code

Description

Set Point

Ramp Soak Step Menu

Press & Hold SET and A/M Keys Together for 3s to Enter

Code

Description

SEC

Timer Unit

LOOP

Program Cycling

PDE

Power Outage Mode

SsB

Safety Start Band

RUN

Program Control

PRO

Program Step Jump

R01

Ramp Time 1

T01

Soak Time 1

Set Temp 1

C01

...

Ramp Time 32

R32

Soak Time 32

T32

Set Temp 32

C32

WWW.AUBERINS.COM

Initial

Setting Range

Remarks

Setting

-1999 ~ +9999

200

See 5.3.1

0 ~ 200

± 20.0

See 5.3.2

0 ~ 5000

See 5.3.3

0 ~ 3000

500

0 ~ 2000

100

2 ~ 120

See 5.3.4

0 ~ 50

See 5.3.5

0.1 ~ 50.0

0.5

See 5.3.6

0 ~ 1

See 5.3.7

outL ~ 200%

200%

See 5.3.8

0 ~ outH

See 5.3.3,

0 ~ 1

section 3)

0 ~ 50

See 5.3.9

See 5.3.10

Reserved

C, F

C/0

See 5.3.11

0 ~ 10

See 5.3.1

0 ~ 1

See 5.3.12

PuL ~ 9999

1300

See 5.3.13

-1999 ~ PuH

0 ~ 255

See 5.3.14

3 for

9600

Initial

Setting Range

Remarks

Setting

PuL ~ PuH

100

See 5.3.15

Initial

Setting Range

Remarks

Setting

0 ~ 1

0 for min.

See 5.3.16

0 ~ 1

See 5.3.17

0 ~ 3

See 5.3.18

0 ~ 100.0

100

See 5.3.19

0 ~ 3

See 5.3.20

0 ~ 64

See 5.3.21

0 ~ 2000

0 ~ 9999

See Section 6

PuL ~ PuH

P3/10