Duevi EZY-LAN HW 4A Посібник з встановлення - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник з встановлення для Система безпеки Duevi EZY-LAN HW 4A. Duevi EZY-LAN HW 4A 13 сторінок. Wireless alarm panel with ethernet + wi-fi + gsm + lte

Друкувати сторінку

•

Wireless supervision: enables / disables the

device presence control

•

Masking control: enable / disable the device

masking control

•

Individual zone setting:

Zone name

Zone type: Volumetric, Door, Shutter,

Vibration, Button

Alarm level: select the alarm level of the

zone between High (L2) / Low (L1)

Zone

mode:

Silent, 24H, Panic, Only use for logic

The zone set as mode "Only use for

logic" cannot be managed within the

sectors as an alarm zone, but can

only be used within a Logic (see

"Logic" section).

Manually excludable: enables / disables

the possibility for the administrator user to

manually exclude the zone

Alert: enables / disables the bell sound

(chime) on the zone at each detection

when the sector is disarmed.

VIDEO-PIR

ATTENTION:

✓ The control panel starting from FW 3.1.14 is

only compatible with VIDEO-PIR updated to

FW version 0.25 or higher

✓ The VIDEO-PIR sensor after updating to the

FW 0.25 version must be set with DIP3=ON

and rebooted

Communication with the sensor now takes place

on a new dedicated radio channel.

The software interface, during manual image

capture, indicates the various stages of image

capture and transfer.

SIRENS

ATTENTION: The control panel is

compatible only with the following models

of siren:

✓ VV-ZELA-RB-868 with FW 0.27 or later

✓ SIRPZ-RB-868 with FW 0.6 or later

•

Device Name: is the name with which the

device is identified in all menus, notifications,

events, etc

•

Tamper: enables / disables the device tamper

signal

•

Wireless supervision: enables / disables the

device presence control

•

Associated

sectors:

sectors the siren will be active

Instantaneous,

Delayed,

indicates

for

•

Visual and sound signals for: Alarm L1, Panic

alarm, Arming, Disarming, System status

12.1.2 IP Devices (Shelly)

It is possible to add and manage Shelly devices

(produced by Allterco Robotics LTD).

The models compatible with the control unit are

the following:

• Shelly 1

• Shelly 1L

• Shelly 2.5

• Shelly RGBW2

• Shelly Plug S

• Shelly Duo

• Shelly Duo - RGBW

In order to be managed by the control panel, the

Shelly device must be connected and configured

as indicated below.

The Shelly must be connected to the same local

network to which the control panel is connected

(via Ethernet or Wi-Fi). For this operation, refer to

the Shelly manual or to the numerous tutorials on

the internet.

The Shelly must have a fixed IP on the local

network (i.e. it must not change over time).

To achieve this, you can proceed with several

methods.

1. First method. Enter the Shelly settings (via

Shelly App or web browser) and program it

with a fixed IP

ATTENTION

✓ Do not assign an IP used by other devices

on the network

✓ Do not assign an IP that is part of the

router's DHCP range

2. Second method. Reserve a fixed IP for the

Shelly device in the router's DHCP settings.

This way the router will always assign the

same IP to Shelly.

Some Shelly models can be configured in

different ways.

For example the Shelly 2.5 can be set in shutter

mode or double relay mode.

This setting must be made before adding the

Shelly to the control panel devices.

The Shelly also must not have password

protection set.

Once the Shelly has been set up as indicated

above, it can be added to the control panel

which

devices by pressing on "Add IP device (Shelly)"

and typing its IP address.