Dunsley Heat Wentworth Інструкція користувача - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція користувача для Внутрішній камін Dunsley Heat Wentworth. Dunsley Heat Wentworth 2 сторінки. Living flame inset convector decorative gas fire, suitable for installation into 400mm 16" and 450mm 18" fireplace openings

Друкувати сторінку
FIG.
4. FRONT
ELEVATION
FIG. 5.
PLAN OF BURNER BAR
••
".e.".".0
••••••••
in
position on burner
bar.
Push well back against fire bed
;
Q·······-ii··········cit····:····tl··········ci>··········Q
in position
in front
of
the
rear ceramic
Fire Bed Retainer.
NOTE:
Tunnel at bottom running from front to rear to give
correct gas ignition
retainer.
FIRE
BED
RETAINER
coai bed fitting
inside the
Fig6.1B.gif
Required - 6 small coals,S
medium coals, 7
in size, but
are easily
selected.
Note coal position in FIG
6.C.
and 6.D. See
gives positions
of
coals.
Position
holes reasonably
clear.
1.
The Wentworth should be serviced at least
Corgi Registered gas engineer, to ensure
free operation.
2.
The chimney or flue
must·
Wentworth.
3.
The chimney or flue must be
continued clearance of combustion products
no excessive build up of
ventilation should be checked
free from
obstruction.
4.
The Wentworth is designed such that it
excessive soot will accumulate on
S.
If excessive deposits of soot are noted
to cool for three to four hours
carried
out.
Any debris from the
must be removed and
any
Gloves should be
worn.
necessary to clean off any soot which
coals, front coal assembly, rear
large pieces of debris are found the chimney should be
inspected and the appliance fully serviced before further use,
to maintain good
combustion.
after removal of the ceramic coals and
jet holes in the burner are
alter the quantities of the coals
6.
The rear ceramic bed is made of pure
dropped.
If handled with reasonable care when
position it will last
indefi"itely.
It is precision made and designed to be placed
position to give a good
performance.
unless it is broken. The black coat will not
chipped off, if not handled with care when
for servicing. To meet this possibility we
of black ceramic paint complete with touch up
7.
If for any reason any of the coals or fire bed are removed
must be replaced carefully and correctly, see FIG
6A, B, C and
D.
8.
Rubbish or combustible material must not be thrown,
onto the fuel
bed.
Do not disturb the
angle coals. Coals vary a little
aiso
letter chart
below, which
coals
on
ceramic bed keeping the flame
Four small
coals
on back
resting
against
convector back.
One small
coal
at each end of
third
row.
M:-
Five medium coals .
A:- Seven Angle
coals.
S
Small
Coals
=
M
Medium
=
A
Angle
Coals
=
)
.'.
ANGLE
,
~~.
COAL
'\'
J
FRONT
The angle
coals
sit on
the
short base,
upright with
the long
surface
facing
front.
once per year by a
many years
of
trouble
be swept
before installation
of
checked annually to ensure
and that there is
soot.
Any
purpose-provided
periodically
to
ensure
that it
is
very
unlikely any
any part
of
the
fire.
the fire
should
before any servicing work is
chimney or other sources
soot
formed
should
be cleared.
A soft brush should be used if it
may
have formed on the
ceramic
bed
or
burner.
A vacuum
cleaner may
be used
supports.
Ensure all gas
clear.
Do not
change
the layout
used.
ceramic
and will break if
placing
It will not
break
in
use.
in the correct
It will not
require replacing
burn off, it can be
removing or replacing
supply a
small bottle
brush.
4,
Sand
fuel bed.
58004
row
Coals
must
the
t}";e
is
be left
is
If
any
or
in
they
or
put,