ADEMCO LYNXR Посібник із швидкого старту
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Система безпеки ADEMCO LYNXR. ADEMCO LYNXR 8 сторінок.
Також для ADEMCO LYNXR: Посібник із швидкого старту (8 сторінок)
Друкувати сторінку
®
8 /
Introduction
This Quick Start Guide can help you install the LYNX (non-rechargeable) and LYNX-R
(rechargeable ) quickly and easily by providing the basic steps for installation using the built-in
defaults. For more detailed information and important notes, refer to the LYNX and LYNX-R
Installation Instructions.
The following steps assume that one of the system's default tables will be used.
For programming data values and Powerline Carrier Devices other than those listed in the default
tables, see the Installation Instructions.
Default Table Summary
Zone
1
2
3
4
5
6
7
8
9
26
27
28
29
30
31
32
33
92
99
User
Code
Install
Code
Entering Program Mode: installer code + 8 0 0
Interactive Mode
* 56 Enhanced Zone Programming
* 83 Sequential Mode
*84 Assign Zone Voice Descriptors
Exiting Program Mode:
NOTES: •
4XL.N6WDUW*XLGH
LYNX-R is not intended for UL985 Household Fire applications.
Table 1
-------
front door
back door
window
motion detector
-------
-------
-------
-------
loop 3 arm away
loop 2 disarm
loop 4 arm stay
loop 1 restore device 1
loop 3 arm away
loop 2 disarm
loop 4 arm stay
loop 1 restore device 1
duress
silent alarm
1-2-3-4
4-1-1-2
* 99 allows re-entry into the Program mode using Installer Code + 8 0 0.
* 98 inhibits re-entry into the Programming mode using the Installer Code.
Tables 2 and 4 support the automatic paging feature (open/close events reported to pager phone
number),and a Powerline Carrier Device programmed as device 8, which closes and stays closed
upon burglary alarms and restores after bell timeout. For other applications or actions (e.g., using a
pulsing siren), see the *80 Device Programming Menu Mode section of the Installation Instructions.
•
Primary report format for all tables is Ademco's Contact ID reporting. Tables 2 and 4 also use Contact
ID for secondary reporting. Tables 1, and 3 use 4+1 format for secondary reporting.
•
Table 2 records all events in the event log. Tables 1, 3, and 4 record only alarms, alarm restores,
troubles, and trouble restores in their event logs.
Table 2
Table 3
-------
-------
front door
front door
back door
back door
Garage door
window
motion detector
window
smoke detector
window
-------
window
-------
motion detector
-------
smoke detector
loop 3 arm away
loop 3 arm away
loop 2 disarm
loop 2 disarm
loop 4 arm stay
loop 4 close device
loop 1 restore device 1
loop 1 restore device 1
loop 3 arm away
loop 3 arm away
loop 2 disarm
loop 2 disarm
loop 4 arm stay
loop 4 close device
loop 1 restore device 1
loop 1 restore device 1
duress
silent alarm
1-2-3-4
4-1-1-2
Used to Program
Zone characteristics, report codes, and serial numbers
5800 Series transmitter serial numbers
Voice descriptors for each zone
/<1;5
Table 4
-------
front door
back door
window
window
window
window
motion detector
smoke detector
loop 3 arm away
loop 2 disarm
loop 4 close device
loop 1 restore device 1
loop 3 arm away
loop 2 disarm
loop 4 close device
loop 1 restore device 1
duress
silent alarm
silent alarm
1-2-3-4
4-1-1-2
N8889QSV2 6/99
/<1;
duress
1-2-3-4
4-1-1-2