ADEMCO LYNXR Series Посібник із швидкого старту - Сторінка 5

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Система безпеки ADEMCO LYNXR Series. ADEMCO LYNXR Series 8 сторінок.

Друкувати сторінку
Step
3.
b
2)
(Cont.)
3)
Note:
d.
Delete Serial Number -
*
1)
Set RF House ID in the wireless keypads as follows:
4.
a.
5827 wireless keypad - Set the keypad's DIP switches to the RF House ID programmed in field *24.
b.
5804BD button key - Set the RF House ID per its instructions.
c.
Powerline Carrier Devices - Set their House ID to "A," (programmed as "0") or use field *25 to change the ID to avoid
conflicts with existing installations.
5.
Set the Real-Time Clock as follows:
a.
Enter time/date setting mode by entering the User Code + FUNCTION + [63].
b.
The hour prompt is displayed. Enter the correct hour, then press [*] to accept and advance.
c.
For each subsequent prompt, enter the correct value, then press [*].
d.
The system will exit this mode automatically after entering the year, or if no keys are pressed for 1 minute.
Test the system as follows:
6.
a.
After installation and programming, enter Installer Code + TEST.
b.
To exit Test mode, enter Installer Code + OFF.
Assign desired User Codes by following the procedures on the next page and in the User Guide. Show the user how to perform
7.
the various system functions.
Perform site-initiated downloader session (to load central station ID) by Installer Code + [#] + [1].
8.
5800 Series Transmitter Loop Numbers: The following illustration shows the compatible transmitters and their associated
input types and loop designations.
LOOP 4
YOU MUST
ENROLL
THIS
BUTTON
5 8 0 0 R L
5 8 0 1
ENROLL AS
S E T
"UR" OR "RF"
H O U S E I D
LOOP 1
5806/5807/5808/5808LST
5814
ENROLL AS "RF"
ENROLL AS "RF"
1
LOOP 2
2
4
3
(REED)
5
7
6
8
*
9
0
LOOP 3
#
(TERMINALS)
LOOP 1
(INTERNAL
SHOCK
SENSOR
5 8 2 7
5 8 1 9 S ( W H S & B R S )
PROGRAM
ENROLL AS "RF"
HOUSE ID
U L
The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5804WATCH, 5814, 5816TEMP, 5819, 5819S(WHS &
BRS), and 5850(GBD) transmitters are not intended for any UL installations.
Manual Entry - Enter the 7-digit serial number printed on the transmitter. If you enter an
incorrect digit, press the [#] key to backup to prompt (1A) and start over. When all seven digits
are entered press the [*] key.
Once all 7 digits have been entered, press the [*] key. If less than 7 digits are entered, the
keypad will emit a single long beep and return to the (1A) prompt without displaying the
"L". If more than 7 digits have been entered, the first 6 digits will be saved along with the
last digit that was entered (entering 123456789 yields the serial number 1234569).
If 52 seconds passes and no entry has been made, the system returns to prompt (1A).
This prompt can be used to delete the serial number programmed for the zone.
Enter "0" to discard delete request or "1" to confirm
LOOP 3
LOOP 2
LOOP
LOOP
LOOP 1
1
1
5 8 0 2 M N
5 8 0 2 M N 2
ENROLL AS
ENROLL AS
"UR" OR "RF"
"UR" OR "RF"
LOOP 2
(REED)
LOOP 1
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
5 8 1 6
5 8 1 6 M N
ENROLL AS "RF"
ENROLL AS "RF"
LOOP 1
(SOUND)
5 8 4 9
5 8 5 0 ( G B D )
ENROLL AS "RF"
ENROLL AS "RF"
Action
LOOP 3
LOOP 4
O N
YOU MUST
LOOP 2
O F
F
ENROLL
LOOP 1
THIS
LOOP 3
BUTTON
5804/5804E
5 8 0 4 B D / 5 8 0 4 B DV
ENROLL AS "BR"
PROGRAM HOUSE ID
LOOP 2
(REED)
LOOP 1
LOOP 1
(TERMINALS)
(TEMP
SENSOR)
5 8 1 6 T E M P
5 8 1 7
ENROLL AS "RF"
ENROLL AS "RF"
LOOP 1
(MOTION)
(Green)
(Red)
(Yellow)
5 8 9 0 / 5 8 9 0 P I
ENROLL AS "RF"
-5-
LOOP 4
YOU MUST
LOOP 2
ENROLL
THIS
LOOP 4
BUTTON
YOU MUST
1 : 1 5
ENROLL
: 0 0
THIS BUTTON
1 : 1 3
: 1 6
LOOP 3
LOOP 1
•
• •
•• •
• • ••
• •
•
•
5804WATCH
ENROLL AS "BR"
LOOP 1
(PRIMARY)
LOOP 2
(REED)
LOOP 2
(AUX.
CENTER)
LOOP 3
LOOP 1
(AUX.
LOOP 3
RIGHT)
(TERMINALS)
5 8 1 8
ENROLL AS "RF"
ENROLL AS "RF"
LOOP 1
LOOP 1
LOOP 2
5809
ENROLL AS "RF"
LOOP 1
(TERMINALS)
5 8 1 9
01009-012-V1