Emerald Planet EP-RF-Li10 Посібник користувача - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник користувача для Димова сигналізація Emerald Planet EP-RF-Li10. Emerald Planet EP-RF-Li10 5 сторінок.

Друкувати сторінку

IMPORTANT SAFETY INFORMATION

1: The test button accurately tests the smoke alarm functions. Do not

use any other test method. Test smoke alarms weekly to ensure

proper operation.

2: If you're sure it isn't a real alarm, open windows or fan the air

around the smoke alarm device to silence it.

3: Observe and follow all local and national electrical and building

codes for proper installation.

4: This smoke alarm is designed to be used in residential premises

only. Do not install in non-residential buildings. This smoke alarm is

not a substitute for a complete alarm system.

5: Install a smoke alarm in every room and on every level of the home.

Smoke may not reach the smoke alarm for many reasons. For

example, if a fire starts in a remote part of the home, on another

level, in a chimney, wall, roof, or on the other side of a closed door,

smoke may not reach the smoke alarm in time to alert household

members. A smoke alarm will not promptly detect a fire except in

the area or room in which it is installed.

6: Smoke alarms may not alert every household member every

time. The alarm sound is loud in order to alert individuals to a

potential danger. However, there may be some circumstances

where a household member may not hear the alarm (i.e. outdoor

or indoor noise, deep sleepers, drug or alcohol usage, the hard of

hearing, etc.). If you suspect that this smoke alarm may not alert a

household member, install and maintain specialty smoke alarms.

Every household member must hear the alarms warning sound

and quickly respond to it to reduce the risk of injury, or death that

may result from fire.

7: Smoke alarms can only activate when they detect smoke or detect

combustion particles in the air. They do not sense heat, flames,

or gas. This smoke alarm is designed to give audible warning of a

developing fire. However, many fires are fast - burning, explosive,

or intentional, and others are caused by carelessness or safety

hazards. In these circumstances, there may be insufficient smoke

to activate the alarm QUICKLY ENOUGH to ensure safe escape.

8: Smoke alarms have limitations. This smoke alarm is not foolproof

and is not warranted to protect lives or property from fire. Smoke

alarms are not a substitute for insurance. Homeowners and renters

should insure their lives and property. In addition, it is possible for

the smoke alarm to fail at any time. For this reason, you must test

the smoke alarm weekly and replace unit every 10 years.

DO NOT INSTALL SMOKE ALARMS IN THE

FOLLOWING PLACES

1: Near appliances or areas where normal combustion regularly

occurs (kitchens, near furnaces, open fireplaces, hot water

heaters etc.).

2: In areas with high humidity, like bathrooms or areas near

dishwashers or washing machines. Install at least 10 feet

away from these areas.

3: Near air returns or heating and cooling supply vents. Install

at least 3 feet away from these areas. The air could blow

smoke away from the detector, interrupting its alarm.

4: In rooms where temperatures may fall below 5° or rise above

45°, or in humidity higher than 85%. These conditions could

reduce battery life or cause a false alarm.

5: In extremely dusty, dirty, or insect–infested areas influence

particles interfere with smoke alarm device operation.

OPERATION

ACTIVATION

To activate the smoke alarm, align the mounting plate and

turn it clockwise until it snaps into place. The battery is now

connected and the smoke alarm is active.

TESTING

Test the unit to ensure proper operation by pressing the test button,

this will sound the alarm if the electronic circuitry, horn, and battery

are working. If no alarm sounds, please refer to the "Troubleshooting"

section for solution.

EMERALD PLANET HEAD OFFICE - SYDNEY Unit 2 / 29 Mitchell Road, Brookvale NSW 2100 Australia P 02 9466 6000

DO NOT USE AN OPEN FLAME TO TEST YOUR ALARM, YOU

COULD DAMAGE THE ALARM OR IGNITE COMBUSTIBLE

MATERIALS AND START A FIRE.

CAUTION: DUE TO THE LOUDNESS (85 DECIBELS) OF THE

ALARM, ALWAYS STAND AT ARMS-LENGTH AWAY FROM

THE UNIT WHEN TESTING. TEST THE ALARM WEEKLY TO

ENSURE PROPER OPERATION. ERRATIC OR LOW SOUND

COMING FROM YOUR ALARM MAY INDICATE A DEFECTIVE

ALARM, PLEASE REFER TO "TROUBLESHOOTING" SECTION

FOR SOLUTION.

NOTE: WEEKLY TESTING IS REQUIRED.

LED INDICATORS

Red LED-Flashing once every 40 seconds: indicates that the

smoke alarm device is operating properly.

Red LED-Flashing when the test button is pressed, or when the

smoke alarm device senses particles of combustion and goes

into alarm (constant pulsating sound), the red LED will flash

once per second. The flashing LED and pulsating alarm will

continue until the air is cleared or test button is released.

Red LED-Alarm silencer (Hush mode) indication: The red LED

will flash once every 8 seconds, indicating the smoke alarm

device is in the alarm silence (Hush) mode.

Low battery indication - An intermittent "chirp" with red

LED flashes once every 40 seconds: indicates that the smoke

alarm device is low on battery, you may press the test button

to pause the alarm for 10 hours, but it will reset automatically

after 10 hours.

Fault indication - The alarm chirp occurs every 40 seconds.

NOTE: WHEN THE UNIT CHIRPS ONCE EVERY 40 SECONDS,

YOU CAN PRESS THE TEST BUTTON TO TEMPORARILY

PAUSE THIS WARNING TONE FOR 10 HOURS. IT CAN STILL

NORMALLY DETECT SMOKE DURING THIS PERIOD, IT ONLY

REMOVES NUISANCE WARNING TONE. YOU CAN REFER TO

"TROUBLESHOOTING" FOR SOLUTION. IF THERE ARE STILL

FAILURES, YOU MUST REPLACE IT WITH A NEW ALARM AT

ONCE OR CONTACT YOUR RETAILER DURING WARRANTY

PERIOD.

ALARM SILENCE (HUSH MODE)

To silence an alarm, push the test button, it will pause the

alarm for approx. 10 minutes. The red LED will flash once every

8 seconds, it indicates the smoke alarm is running in "silence

mode". Smoke alarms are designed to minimise nuisance

alarms. Combustion particles from cooking may set off the

alarm if the alarm is located close to the cooking area.

Large quantities of combustible particles are generated from

spills or when grilling/frying. Using the fan on a range hood

that vents to outside (non-recirculating type) will also help

remove these combustible particles from the kitchen. The

alarm silence (test button) is extremely useful in a kitchen area

or other areas prone to nuisance alarms. The silence feature is

to be used only when a known alarm condition, such as smoke

from cooking activates the alarm.

The smoke alarm will automatically reset after approximately

10 minutes, if after this period, particles of combustion are still

present, the alarm will sound again. The alarm silencer (silence

mode) can be repeatedly until the air has been cleared of the

condition causing the alarm.

CAUTION: BEFORE SILENCING THE ALARM IDENTIFY THE

SOURCE OF SMOKE AND ENSURE THERE IS NO RISK OF

FIRE.

NOTE: DENSE SMOKE WILL OVERRIDE THE SILENCE MODE

AND THE ALARM WILL SOUND A CONTINUOUS ALARM

AGAIN.

DANGER: IF THE ALARM SOUNDS, AND IT IS NOT BEING

TESTED, IT MEANS THE UNIT IS DETECTING SMOKE AND

REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.