HID iCLASS SE RKLB40 Посібник користувача - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник користувача для Зчитувач карток HID iCLASS SE RKLB40. HID iCLASS SE RKLB40 4 сторінки. Biometric reader
Друкувати сторінку
U S E R GU I D E
3. The selected language will appear on the screen.
Choose 1. Yes to confirm or 2. No to cancel and go back to
the language selection dialog.
Language
English
1. Yes
2. No
Note: Language selection will restart until a language is chosen.
4. From this point on, all screens will display in the selected
language.
Note: To change the language after the Initial Setup, go to the
Administration menu and select Configuration (see Section 4.2.3:
Configuration Menu Functions).
2.1.2 Select Credential Type
Once the language is chosen, Initial Setup advances to the Credential
Type menu. This configures the credential types that the Reader will
enroll. To read Seos credentials, Seos must be selected during initial
set-up to allow the Seos Site Key to be entered, after the Site Key
has been entered the Credential type configuration can be changed
to allow iCLASS credential to be enrolled. Credential types setting
does not configure the card types the reader will read, this is a factory
configuration and by default the reader will read both iCLASS and
Seos.
Credential type
1. Seos
2. iCLASS
1.
To select the Template Type:
Select 1. Seos. This Mode enrolls Seos cards but will not
enroll iCLASS or iCLASS SR cards.
Select 2. iCLASS. This Mode enrolls only iCLASS or iCLASS
SR cards.
2. Once you make your choice a confirmation dialog appears.
Choose 1. Yes to confirm or 2. No to cancel and return to the
Template Type menu.
2.1.3 PIN Requirement (Local PIN Verify)
Note: PIN Required MUST be set to Not Required UNLESS reader
is ordered with Local PIN Verify factory configuration option. Local
PIN Verify is used extremely infrequently and therefore PIN Required
MUST be configured to Not Required unless for special Local PIN
Verify applications.
Note: If set to Required and the reader is ordered without Local PIN
Verify configuration option, the reader will need to be reset via the
supplied SE BIO Initial Setup Reset Cards to PIN Required set to Not
Required.
Note: When the reader is order from factory WITHOUT Local PIN
Verify configuration option, PIN data entered on keypad will be sent to
the door controller for verification.
PIN Requirement is ONLY applicable to readers with Local PIN Verify
factory configuration option. It selects whether a PIN enrolled to the
card by the reader must be verified locally by the reader before the
card data is sent to the door controller. If Required is chosen, a PIN
number will be asked for when Users and Admins are enrolled, and
also when cards are presented to a Reader to gain access. (For more
information on PINs, see Second page of Configuration options in
Section 4.2.3: Configuration Menu Functions).
1. Select 1. Required or 2. Not Required.
2. When you make your choice a confirmation dialog appears.
Choose 1. Yes to confirm or 2. No to cancel.
hi d g l o b a l.com
iCLASS SE Biometric Reader
2.1.4 Operational Mode
Once the Template Type and PIN Requirement choices are made, Initial
Setup advances to the Operational Mode menu.
Mode
1. Reader/Enroller
2. Enroller Only
3. Reader Only
To select the Operational Mode:
Select 1 for Reader/Enroller: The Present Card menu will be the
main interface thereafter. This mode allows the reader to act as
either a reader or enroller.
Select 2 for Enroller Only: The Administration menu will be the
main interface thereafter.
Select 3 for Reader Only: The Present Card menu will be the main
interface thereafter.
Confirm the choice:
Select 1. Yes to confirm.
Select 2. No to cancel and return to the Operational Mode menu.
If you select 1. Yes, a confirmation dialog appears. Choose 1. Yes to
confirm or 2. No to cancel.
This ends the Initial Setup – Functional Selections stage. The next
stage differs, depending on the Template Type chosen.
Note: If the Reader is switched off at this point in the Initial Setup
process it will return to this stage when it is switched back on.
2.2
Initial Setup – Site Key
Note: A Site Key must be entered for all readers with Template Type
set to Seos (including both HID Elite and Standard Key readers),
however, the Site Key is only used by Standard Key readers..
The Site Key setup follows the Operational Mode setup.
The Site Key encrypts the biometric credentials onto the card so
they are unique to each site. The Site Key must be between 6 and 11
characters and must be entered identically onto all readers on that
particular site.
To choose the Site Key:
1. Enter the Site Key and press #.
2. The reader will display Verify Key. Enter the Site Key number
again and press #.
Site Key
Enter PIN
******
Note: If the Site Key number is not entered within the timeout
period the Reader will display Enrollment Failed and return to the
Site Key menu.
3. Once the Site Key value has been successfully entered and
verified, the Reader displays Success! and advances to the next
stage.
An ASSA ABLOY Group brand
RKLB40E; SRD Model: RKCLB40E