HID iCLASS SE RKLB40 Посібник користувача - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник користувача для Зчитувач карток HID iCLASS SE RKLB40. HID iCLASS SE RKLB40 4 сторінки. Biometric reader
Друкувати сторінку
iCLASS SE Biometric Reader
2.3
Initial Setup – Verify Admin
The final stage of Initial Setup registers the Admin card. The Reader
presents two choices: Enroll Admin or Present Card in order to verify
an existing Admin card.
Verify Admin
1. Enroll Admin
2. Present card
Note: The following Enrollment dialog is the same for Initial Setup,
Add Admin, and Add User. The main title at the top of the display
changes to indicate the current function.
2.3.1 Enrollment Dialog
Example: "Enroll Admin" choice in the "Verify Admin" step
The Reader displays:
1. Enroll Admin
2. Present Card
Note: The user should chose 2. Present Card if they already have an
Admin card. When an Admin card is successfully presented to the
Reader (it will ask for a finger to be presented and Local PIN Verify,
if required) this choice will succeed. If there is a failure to present an
Admin card, then an error message is shown and the Verify Admin
menu is re-presented.
1. Select 1. Enroll Admin. The Reader displays:
First Finger
Capture 1 of 3
Put finger on sensor
The Reader will request to capture the first finger three times.
Enroll Admin
First Finger
Capture 1 of 3
Put finger on sensor
Note: The second line on the display will give instructions to the user,
such as Put finger on sensor, Press harder, Move right, Remove finger,
and so on. Also, for each of the three captures it is recommended that
the user fully removes their finger and repositions it slightly differently
on the sensor (e.g., more pressure, to one side a little) as this allows
the sensor to collect more/different information.
The Reader then asks for the second finger to be captured three times.
When the operation is complete the Reader displays Success.
Note: If there is an error, if the fingerprint is not captured, or if the
Reader times out, the Reader displays Authentication Failed and
the sequence returns to the Enroll Admin screen. After three failed
attempts the display reverts to the main menu. In the case of Initial
Setup the display returns to the Verify Admin menu, as you must
successfully enroll a new Admin (or prove that you have already done
so) to exit that step.
2. If a Local PIN Verify number is required, the Reader then
displays:
Keypad PIN
Enter the PIN number and press #. The PIN number can be from
1 to 12 digits. You must the end entry with the # key, unless you
use a 12-digit PIN in which case the Reader accepts the PIN
when the 12th digit is entered and the # key is not required.
The Reader will display Verify PIN. Enter the PIN again and press #.
Note: If the PIN is not entered within the timeout period the
Reader will display Enrollment Failed and will prompt the user
to try again. After three attempts the sequence returns to the
Enroll Admin screen.
hi d g l o b a l.com
RKLB40E; SRD Model: RKCLB40E
An ASSA ABLOY Group brand
3. The Reader then displays:
Write to card
Present card
Present the card to the reader. If successful, the Reader will
reboot into the Operational Mode you have chosen for it and is
ready for normal use.
3. Operation – Reader
In Reader Mode, the display shows the Present Card screen.
iCLASS SE
Present Card
1.
Present the card to the Reader.
2. Follow the on-screen prompts to present a finger to the Reader,
if required.
Note: To ensure a good quality fingerprint acquisition:
Do not press too hard
Do not move finger during acquisition
Leave your finger on the sensor at least 2 seconds
Do not slide or roll your finger across the sensor
3. Enter your Local PIN Verify number, if required.
Note: These requirements can be changed via the Configuration
menu.
4. When successful, the Reader will:
Beep and flash green (LED).
Display Success!
Transmit the access information that is stored on the card to
an attached panel.
Note: If the information provided does not match what is stored
on the presented card, the iCLASS SE Biometric Reader will
prompt the user to try again. After four unsuccessful attempts at
verification the display reverts to Present Card and the user must
start over.
Note: If a card with no fingerprint template is presented the
reader will display "Security Error".
4. Operation – Administration
4.1
Access the Administration Menu
If the Reader is configured to be a Reader/Enroller and the user wishes
to access Administration mode, follow this procedure:
1. The Reader that is configured to be a Reader/Enroller displays
the Present Card menu as its main screen.
2. Before you present a card, select 1 on the keypad.
3. Present an Admin card then remove the Admin card from
the reading field and follow the on-screen prompts to verify
biometric information and Local PIN Verify number as required.
4.2
Administration Menu Functions
From the Administration menu, access the functions below.
Note: Each menu will return to the main menu if it times out (time out
occurs after 8 seconds).
Administration
1. Manage Users
2. Manage Admins
3. Configuration
4. < exit >
4.2.1
Manage Users
This presents the choice of enrolling or verifying a User: the standard
Enrollment dialog is used (see Section 2.3.1: Enrollment Dialog).
U SE R G U I D E