Autonics FS4E-1P2 Посібник з експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Таймер Autonics FS4E-1P2. Autonics FS4E-1P2 4 сторінки. 8-pin plug digital timers with thumb wheel switch
Друкувати сторінку
Ordering Information
This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.
FS
❶
E
-
❷
❶ Display digits
4: 4-digit
5: 5-digit
❷ Output
1P: 1-stage setting (4-digit)
I: Indicator (5-digit)
Product Components
• Product
(+ bracket)
Sold Separately
• 8-pin socket: PG-08, PS-08(N)
Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics website.
12.3
63.8
□48
10.5
■ Bracket
□49.5
30.5
60.3
Connections
Caution
: Refer to the 'specifications' for checking the power supply and control output.
■ FS4E-1P4
5 - 30 VDCᜡ (External power)
PNP
INHIBIT
RESET
0 V
NPN
SOURCE
■ FS5E-I4
5 - 30 VDCᜡ (External power)
PNP
INHIBIT
RESET
NPN
0 V
SOURCE
Error
• When error occurs, the output turns OFF.
• Indicator model does not have error display function.
Display
Description
Troubleshooting
Setting value = 0
Change the setting value anything but 0.
ERR0
❸
❸ Power supply
2: 24 VACᜠ 50 / 60 Hz, 24 - 48 VDCᜡ
4: 100 - 240 VACᜠ 50 / 60 Hz
• Instruction manual
14
■ Panel cut-out
≥ 65
□45
+ 0.5
0
■ FS4E-1P2
5 - 30 VDCᜡ (External power)
PNP
INHIBIT
RESET
NPN
0 V
SOURCE
Specifications
Model
FS4E-1P2
Display digits
4-digit
Character size
W 3.8 × H 7.6 mm
Return time
≤ 500 ms
Time operation
Power ON Start
Min. signal width
RESET, INHIBIT: ≈ 20 ms
Voltage input (PNP)
- input impedance: ≤ 10.8 kΩ, [H]: 5 - 30 VDCᜡ, [L]: 0 - 2 VDCᜡ
No-voltage input (NPN)
Input logic
- short-circuit impedance: ≤ 470 Ω,
- short-circuit residual voltage: ≤ 1 VDCᜡ
- open-circuit impedance: ≥ 100 kΩ
One-shot output time
0.05 to 5 sec
Control output
Relay
Contact type
Time limit SPDT (1c)
Contact capacity
250 VACᜠ 3 A, 30 VDCᜡ 3 A resistive load
Error
Repeat / SET / Voltage / Temp.: ≤ ± 0.01% ± 0.05 sec
Unit weight (packaged)
≈ 90 g (≈ 130 g)
Approval
ᜢ ᜧ ᜫ
Voltage type
AC voltage type
Power supply
100 - 240 VACᜠ ± 10% 50 / 60 Hz
Power consumption
≤ 4.6 VA
(FS5E-1P4)
Power consumption
≤ 3.8 VA
(FS5E-I4)
Power consumption
-
(FS4E-1P2)
≈ 10 years (non-volatile semiconductor memory type)
Memory retention
Insulation resistance
≥ 100 MΩ (500 VDCᜡ megger)
Dielectric strength
2,000 VACᜠ 50 / 60 Hz for 1 min (between all terminals and case)
± 2 kV square-wave noise by
Noise immunity
noise simulator (pulse width 1
㎲)
0.75 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in
Vibration
each X, Y, Z direction for 1 hour
0.5 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in
Vibration (malfunction)
each X, Y, Z direction for 10 min
Shock
300 m/s
(≈ 30 G) in each X, Y, Z direction for 3 times
2
Shock (malfunction)
100 m/s
(≈ 10 G) in each X, Y, Z direction for 3 times
2
Mechanical: ≥ 5,000,000 operations
Relay life cycle
Electrical: ≥ 100,000 operations (250 VACᜠ 3 A resistive load)
Ambient temperature
-10 to 55 ℃, storage: -25 to 65 ℃ (no freezing or condensation)
Ambient humidity
35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)
Protection rating
IP20 (front part, IEC standard)
Mode Setting
RUN
→
Dot for Hour / Min / Sec
[RESET] 3 sec
Dot for Hour / Min / Second
• If there is no RESET key or DIP switch input for 60 sec, it returns to RUN mode.
• [RESET] key: Setting mode ↔ RUN mode
Move the digit when changing the setting value.
Parameter
Display
T1-1 Setting mode
DP
Setting of dot for
T1-2
Hour / Min / Sec
CLR
Output Operation Mode
For the detailed timing chart for operation output mode, refer to the manual.
FS5E-1P4
FS5E-I4
5-digit
W 4 × H 8 mm
-
-
-
≈ 80 g (≈ 120 g)
AC / DC voltage type
24 VACᜠ ± 10% 50 / 60 Hz,
24 - 48 VDCᜡ ± 10%
-
-
AC: ≤ 3.5 VA
DC: ≤ 2.3 W
± 500 V square-wave noise by
noise simulator (pulse width 1
㎲)
[RESET] 3 sec
Setting range
Setting example
-
-
CLR: not divided with dot
5959: 59 m 59 s
SET: divided with dot
0.59.59: 59 m 59 s
→ RUN