Autonics FS4E-1P2 Produkthandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Produkthandbuch für Zeitschaltuhr Autonics FS4E-1P2 herunter. Autonics FS4E-1P2 4 Seiten. 8-pin plug digital timers with thumb wheel switch

Autonics FS4E-1P2 Produkthandbuch
Ordering Information
This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website.
FS
E
-
❶ Display digits
4: 4-digit
5: 5-digit
❷ Output
1P: 1-stage setting (4-digit)
I: Indicator (5-digit)
Product Components
• Product
(+ bracket)
Sold Separately
• 8-pin socket: PG-08, PS-08(N)
Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics website.
12.3
63.8
□48
10.5
■ Bracket
□49.5
30.5
60.3
Connections
᜸ Caution
: Refer to the 'specifications' for checking the power supply and control output.
■ FS4E-1P4
5 - 30 VDCᜡ (External power)
PNP
INHIBIT
RESET
0 V
NPN
SOURCE
■ FS5E-I4
5 - 30 VDCᜡ (External power)
PNP
INHIBIT
RESET
NPN
0 V
SOURCE
Error
• When error occurs, the output turns OFF.
• Indicator model does not have error display function.
Display
Description
Troubleshooting
Setting value = 0
Change the setting value anything but 0.
ERR0
❸ Power supply
2: 24 VACᜠ 50 / 60 Hz, 24 - 48 VDCᜡ
4: 100 - 240 VACᜠ 50 / 60 Hz
• Instruction manual
14
■ Panel cut-out
≥ 65
□45
+ 0.5
0
■ FS4E-1P2
5 - 30 VDCᜡ (External power)
PNP
INHIBIT
RESET
NPN
0 V
SOURCE
Specifications
Model
FS4E-1P2
Display digits
4-digit
Character size
W 3.8 × H 7.6 mm
Return time
≤ 500 ms
Time operation
Power ON Start
Min. signal width
RESET, INHIBIT: ≈ 20 ms
Voltage input (PNP)
- input impedance: ≤ 10.8 kΩ, [H]: 5 - 30 VDCᜡ, [L]: 0 - 2 VDCᜡ
No-voltage input (NPN)
Input logic
- short-circuit impedance: ≤ 470 Ω,
- short-circuit residual voltage: ≤ 1 VDCᜡ
- open-circuit impedance: ≥ 100 kΩ
One-shot output time
0.05 to 5 sec
Control output
Relay
Contact type
Time limit SPDT (1c)
Contact capacity
250 VACᜠ 3 A, 30 VDCᜡ 3 A resistive load
Error
Repeat / SET / Voltage / Temp.: ≤ ± 0.01% ± 0.05 sec
Unit weight (packaged)
≈ 90 g (≈ 130 g)
Approval
ᜢ ᜧ ᜫ
Voltage type
AC voltage type
Power supply
100 - 240 VACᜠ ± 10% 50 / 60 Hz
Power consumption
≤ 4.6 VA
(FS5E-1P4)
Power consumption
≤ 3.8 VA
(FS5E-I4)
Power consumption
-
(FS4E-1P2)
≈ 10 years (non-volatile semiconductor memory type)
Memory retention
Insulation resistance
≥ 100 MΩ (500 VDCᜡ megger)
Dielectric strength
2,000 VACᜠ 50 / 60 Hz for 1 min (between all terminals and case)
± 2 kV square-wave noise by
Noise immunity
noise simulator (pulse width 1
㎲)
0.75 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in
Vibration
each X, Y, Z direction for 1 hour
0.5 mm double amplitude at frequency of 10 to 55 Hz (for 1 min) in
Vibration (malfunction)
each X, Y, Z direction for 10 min
Shock
300 m/s
(≈ 30 G) in each X, Y, Z direction for 3 times
2
Shock (malfunction)
100 m/s
(≈ 10 G) in each X, Y, Z direction for 3 times
2
Mechanical: ≥ 5,000,000 operations
Relay life cycle
Electrical: ≥ 100,000 operations (250 VACᜠ 3 A resistive load)
Ambient temperature
-10 to 55 ℃, storage: -25 to 65 ℃ (no freezing or condensation)
Ambient humidity
35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)
Protection rating
IP20 (front part, IEC standard)
Mode Setting
RUN
Dot for Hour / Min / Sec
[RESET] 3 sec
Dot for Hour / Min / Second
• If there is no RESET key or DIP switch input for 60 sec, it returns to RUN mode.
• [RESET] key: Setting mode ↔ RUN mode
Move the digit when changing the setting value.
Parameter
Display
T1-1 Setting mode
DP
Setting of dot for
T1-2
Hour / Min / Sec
CLR
Output Operation Mode
For the detailed timing chart for operation output mode, refer to the manual.
FS5E-1P4
FS5E-I4
5-digit
W 4 × H 8 mm
-
-
-
≈ 80 g (≈ 120 g)
AC / DC voltage type
24 VACᜠ ± 10% 50 / 60 Hz,
24 - 48 VDCᜡ ± 10%
-
-
AC: ≤ 3.5 VA
DC: ≤ 2.3 W
± 500 V square-wave noise by
noise simulator (pulse width 1
㎲)
[RESET] 3 sec
Setting range
Setting example
-
-
CLR: not divided with dot
5959: 59 m 59 s
SET: divided with dot
0.59.59: 59 m 59 s
→ RUN