Dynasty DYN-1614 Інструкція з монтажу

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Система відкривання дверей Dynasty DYN-1614. Dynasty DYN-1614 2 сторінки.

Друкувати сторінку

PARALLEL ARM (PUSH SIDE)

P.A Plate

Power adjustment

nut

2-3/4

(70)

3/8

(9.5)

(51)

Door

Frame

5/16

(8) 7/16

(11)

Dimension"A"

Dimension"B"

Opening Angle

Inch

TO 100°

9-1/4

235

7-5/8

194

*101° TO 131°

7-3/4

197

6-1/8

156

146

4-1/8

5-3/4

105

*OVER 131°

* Recommended mounting for meeting ADA compliance

* When door closer is installed and adjusted to conform to ADA

reduced opening force requirements (5 lbs max.), it may not have

adequate closing force to reliably close and latch the door.

INSTALLATION STEPS:

1. Select degree of opening and use dimensions shown or attached template to locate 4 holes on

underside of frame for P.A plate.

2. Prepare door and frame for fasteners. See "Preparation for Fasteners", Figure 1 , Page 1.

3. Before installing closer body, set spring power for closer using Power adjustment chart, Page 1.

4. Disassemble forearm from main arm by removing elbow washer and screw.

Remove the foot from the forearm and discard.

5. Attach closer to door with Power adjustment nut toward hinge .

6. Attach P.A plate to top frame as shown.

7. Use adjustable wrench to rotate the bottom s pindle by 45° toward the hinge edge .

Hold it and Place main arm on top spindle so that the " B' (Right hand door) or ' A" (Left hand door) lines up with

spindle flat . Secure main arm and spindle by tightening spindle bolt.

8. Fasten forearm to P.A plate using screw included in screw pack.

9. When the door is closed, adjust forearm length to set arm elbow about 1-1/2"(38mm) from door when

connected to main arm. Use washer and screw provided to secure pivot connection. Tighten locknut.

10. Snap the pinion cap over spindle at the bottom of closer.

11. Adjust closer. (See Page 2)

Improper installation may result in personal injury or property damage.

！

Caution

Follow all instructions carefully please.

(76)

3/4

(19)

Speed Regulating

9-1/16

Valves

(230)

Left hand door illustrated.

Same dimensions apply to

right hand door.

Door Leaf

Measured from hinge Center.

Dimensions are in inches

1-1/2

(38)

Not To Scale

Pinion flat

For right hand door

For left hand door

door for closer body and 4 holes

Installation Selection:

Door

Frame

Door

Leaf

Regular Arm(Pull Side)

See Page 2.

Preparation for Fasteners-Figure 1.

TOOLS REQUIRED

(mm)

Closer Body

Pinion Cap

Pinion flat

How to tell the hand of a door.

Hinge side of door

Stop side of door

This is a left hand door

Door opening control

Caution:

Do not back valves out of

closer or a leak will result.

ATTENTION:

Backcheck(BC) valve controls the

hydraulic resistance to door opening in

backcheck range. NEVER close this

valve completely.

It is not to provide a positive stop.

DYN-1614,DYN-1636 DOOR CLOSER

Top Jamb(Push Side)

See Page 3.

METAL

WOOD

3/16"

*Pilot Hole Required

1/4"-20

Components

P.A Plate

Foot

Elbow washer

Plastic cover

Rod

& Screw

(Optional)

Lock

Arm Screw

Nut

Screw Pack

Main Arm

Pull side

Hinge side of door

Stop side of door

Push side

This is a right hand door

Closed

Backcheck

Installation Instructions

Grade 1, Meets ANSI A156.4

Parallel Arm(Push Side)

See Page 4.

Self Drilling /Tapping

Sleeve Nut and Bolt

screws

Wood and Metal

Drill 9/32" thru from

Closer side

For wood, drill 3/16" hole

3/8" Drill other Side

Check building and fire

Machine Screws

codes to see if your

application requires the

#7 Drill, 1/4"-20 Tap

use of sleeve nuts and

bolts.

Power 1 to 4 setting & door width

Regular & Top Jamb Installation

Parallel Arm Installation

Maximum Size of Door Width (Factory Preset as size 3)

Size

Interior Exterior

Exterior

Size

Interior Exterior

Full 360°

Inswing

Outswing

Turns

8 Turns

28''

C.C.W

5 Turns

36''

30''

C.C.W

42''

36''

30''

36''

0 Turns

6 Turns

48''

36''

42''

36''

C.W

Power 3 to 6 setting & door width

Regular & Top Jamb Installation

Parallel Arm Installation

Maximum Size of Door Width (Factory Preset as size 4)

Size

Interior Exterior

Exterior

Size

Interior Exterior

Full 360°

Inswing

Outswing

Turns

7 Turns

42''

30''

36''

30''

C.C.W

0 Turns

48''

36''

42''

36''

42''

C.C.W

54''

42''

48''

42''

4 Turns

7 Turns

54''

60''

48''

54''

48''

C.W

C.W-Clockwise

C.C.W-Counter-Clockwise

Door closing control

Caution:

Do not back valves out of

closer or a leak will result.

Closed

Latch

10°

ATTENTION:

Adjust closing time between

4 to 6 seconds from 90°.

USE of the door by

handcapped,elderly or small

children may require longer

closing time.

Standard closing cycle