Centurion D2 Turbo Посібник з монтажу - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник з монтажу для Відкривач воріт Centurion D2 Turbo. Centurion D2 Turbo 9 сторінок. Domestic sliding gate operator theft-resistant nut and padlock kit
Також для Centurion D2 Turbo: Посібник зі встановлення кишенькових пристроїв (13 сторінок), Посібник зі встановлення кишенькових пристроїв (2 сторінок), Посібник з монтажу (2 сторінок)

Друкувати сторінку

1. Connect All Wiring

9.2. Ensure that all low-voltage systems (less than 42.4V) are

suitably protected from damage, by disconnecting all

sources of power such as chargers and batteries before

doing any work.

9.3. All electrical work must be carried out according to the

requirements of all applicable local electrical codes.

It is recommended that a licensed electrical contractor

perform such work.

Connect all wiring

Wire the controller to the required input and output devices as per the

wiring diagrams on the right-hand side.

Refer to the illustration of the D2 Turbo Low-Voltage controller, which

shows the position of the Function and Setting Dials, the status

LED, and the select/toggle

All programming is done by means of two rotary dials, a pushbutton,

and the bi-colour (red and green) status LED.

The rotary Function Dial selects the required function you wish to

set. This is selected first.

Secondly, the rotary Setting Dial dials in the actual setting for the

function selected.

10A. Using the pushbutton and status LEDs

 To select a particular setting, press the

 The status LED indicates the status of the setting

 A green status LED indicates that particular setting is selected

 A red status LED indicates it is Off or not selected

If the setting is a single fixed value, e.g. 15 second

Autoclose time, then the pushbutton acts as a select.

If the setting has an option such as On/Off, or Hi/Lo

then the

 If the status LED is green, then the first option is selected

 If the status LED is red, then the second option is selected

10B. Using the Function Dial

The Function Dial has six different settings that may be selected:

 RUN:

 A - LIMITS:

 B - REMOTES:

 C - AUTOCLOSE: Allows for different Autoclose times to be set

 D - MODE: Allows for different modes of operation to be set

 E - PROFILE:

10C. Using the Setting Dial

The Setting Dial has six different positions, which allow the function

required, to be selected.

Function dial

A - LIMITS

B - REMOTES

C - AUTOCLOSE

D - MODE

E - PROFILE

Use toggle pushbutton to select preference.

For D - MODE, green status LED=On; red status LED=Off

For E - PROFILE, green status LED=High; red status LED=Low

9.1. Always check that the circuit breaker in the

electrical panel is in the OFF position, and that

all high-voltage circuits (more than 42.4V) are

completely isolated from the mains supply

before doing any work.

pushbutton will act as a toggle.

Fully anti-clockwise. The unit must be left in this

position for 'Normal run' operation

Sets up the gate open and closed positions

automatically

Allows for CENTURION remotes to be added or

deleted

Allows for specific gate profiles to be toggled

On/Off, High/Low, backup and restore functions

Setting dial (Ring position-Dial position)

A-1 Automatic; Start with gate closed

B-1 Learn a transmitter button to TRG

B-2 Learn a transmitter button to PED

B-3 Learn a transmitter button to LCK

B-4 Delete a transmitter

B-5 Delete all transmitters

C-1 Autoclose off

C-2 Autoclose after 5 seconds

C-3 Autoclose after 10 seconds

C-4 Autoclose after 15 seconds

C-5 Autoclose after 30 seconds

C-6 Autoclose after 45 seconds

D-1 Standard Mode

D-2 Open Only Mode

D-3 Reversing Mode

D-4 PIRAC Mode

D-5 Pre-Flash Mode A

D-6 Pre-Flash Mode B

E-1 Positive Close Mode

E-2 Speed

E-3 Sensitivity

E-4 Backup to Backup Memory Module

E-5 Restore from Backup Memory Module

pushbutton.

pushbutton

Off