KitchenAid KICU500 Series Інструкція з монтажу Посібник з монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Варильна поверхня KitchenAid KICU500 Series. KitchenAid KICU500 Series 12 сторінок. 30" (76.2 cm) electric induction cooktop
Також для KitchenAid KICU500 Series: Інструкція з монтажу Посібник з монтажу (12 сторінок)
Друкувати сторінку
INSTALLATION REQUIREMENTS
s :xnd
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Tape measure
•
Marker or pencil
•
Flat-blade screwdriver
•
Pliers
•
Phillips head screwdriver
•
1¼. drill bit
•
Hand or electric drill
•
Jigsaw
•
Level
Parts supplied
•
Brackets (2)
•
21/2 '' (6.4 cm) clamping screws (4)
•
#8 x 3/8"(9.5 mm) sheet metal screws (4)
Parts needed
•
A UL listed or CSA approved strain relief
•
UL listed wire connectors
Check local codes. Check existing electrical supply. See
"Electrical Requirements"
section.
It is recommended
that all electrical connections
be made by a
licensed, qualified electrical installer.
Make sure you have everything needed for correct installation. It
is the responsibility
of the installer to comply with the installation
clearances specified in these instructions.
IMPORTANT:
Observe all governing codes and ordinances.
When installing cooktop,
use minimum dimensions given.
•
To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is to
be provided, the risk can be reduced by installing a range
hood that projects horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
•
It is the installer's responsibility
to comply with installation
clearances specified on the model/serial rating plate. The
model/serial
rating plate is located on the underside of the
cooktop burner box.
30" (76.2 cm) cooktop model/serial rating plate location
(models GCI3061, ICI500, KICU500)
A
A. Model/serial rating plate location
•
Check the cooktop base for an approved installation label.
Verify approved oven model number that can be installed with
your cooktop model number. If you don't find this label, your
cooktop should not be used over a built-in oven.
•
Ovens approved for this type of installation will have an
approval label located on the top of the oven. If you do not
find this label, contact your dealer to confirm that your oven is
approved. Refer to oven manufacturer's
Installation
Instructions for approval for built-in undercounter
use and
proper cutout dimensions.
•
When installing cooktop over an undercounter
built-in oven,
do not fasten cooktop to countertop with clamps or seal
cooktop to countertop.
This will make the cooktop easier to
remove if future servicing becomes necessary.
•
Use the countertop opening dimensions that are given with
these Installation Instructions. Given dimensions are
minimum clearances and provide 0" (0 cm) clearance.
•
Grounded electrical supply is required. See "Electrical
Requirements"
section.
Product Dimensions
30" (76.2 cm) Cooktop
A
,__jL
C
Models G013061
Model I01500
Models KICU500
A. 21%6" (54.1cm)
A. 20½" (51.0 cm)
A. 21%6" (54.1cm)
B. 30%6" (77.0 cm)
B. 30%6" (77.0 cm)
B. 303/4 '' (78.2 cm)
C. 2%" (6.0 cm)
C. 2%" (6.0 cm)
C. 2%" (6.0 cm)
2