Gardena 5700 Інструкція з експлуатації Посібник з експлуатації - Сторінка 6

Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Газонна та садова техніка Gardena 5700. Gardena 5700 10 сторінок. Power scrubbing brush

Друкувати сторінку

6. Putting into operation

Attention !

Delivery condition

Working with high pressure !

from the manufacturer

For safety reasons, the

motor starts only when

the operating lever

for the

gun is pressed down. The

Position "MIX"

safety knob

is exclusively

for prevention of unintentional

use, and not to be used to lock

the operating lever

during

The concentration of cleaning

operation.

agent can be regulated as

required.

6.1 Operation using one of

Replacing cleaning rings

the nozzles (fig. H / J)

1. Plug the mains connector

The cleaning rings

into a 230-V a / c socket outlet.

can be replaced

2. Open the water tap.

in this position.

3. Set the dispensing

unit adjust-

Setting the mix ratio (fig. K)

ment knob to

this position:

4. Switch the equipment on:

Turn the ON / OFF switch

required within the range of this

to position I (fig. H).

symbol (fig. K). The cleaning rings

5. Unlock the high-pressure pistol

can be used with all of the tools

(press safety knob

) and

supplied and mixed into the water

press the high-pressure pistol

at any working pressure. The

operating lever

(fig. J).

mixing pot is transparent so that

the cleaning ring consumption

6.2 Adjusting the Vario nozzle

is visable.

(fig. I)

Inserting cleaning rings (fig. K)

The Vario nozzle can be adjusted

The GARDENA Power Scrubbing

to any position, from a hard jet

Brush is fitted with a dispensing

to a flat jet of water. Turn the

unit. Cleaning rings can be in-

nozzle to set the jet required, as

serted as follows:

indicated by the direction of the

1. Turn the adjusting

arrow shown in figure I :

knob on the dis-

Flat jet in the clockwise direction

pensing unit to

(fig. I 1)

this position:

Hard jet in the anticlockwise

direction (fig. I 2)

Please read section 6.6 on termi-

in this position ! There is a

nating work.

danger of damaging the unit.

2. Unscrew the dispensing cup

6.3 Working with cleaning

from the dispensing unit.

rings

3. Place cleaning rings in the

dispensing cup.

Operating the dispensing unit

4. Screw the dispensing cup

(fig. K)

back onto the dispensing unit.

The dispensing unit has 3 main

5. Turn the adjusting knob

positions which can be set as

on the dispens-

follows:

ing unit to

this position:

6.4 Switching on for working

(fig. C)

Water throughput

Hold the high-pressure gun, pre-

without the addition

ferably with both hands as shown

of cleaner.

in figure C. Hold the handle with

the operating lever

pressure gun with one hand and

This position will

guide the direction of the high-

dispense cleaning

pressure gun with the other hand.

agent.

6.5 Working with the power

scrubbing brush

The power scrubbing brush is

suitable for cleaning dirty surfaces

such as e.g. tiles, natural stone

slabs, concrete slabs etc. without

the use of water jets. For easier

handling there are 2 working

positions possible (each turnable

180°).

The mixing ratio

cleaner / water can

Adjusting the working

be adjusted as

positions (fig. L)

To change the working position

proceed as follows:

1. Unscrew the upper nut

extension handle.

2. Pull the power scrubbing brush

with adaptor out of the bayonet

socket and turn it 180°.

3. Push the bayonet of the power

scrubbing brush back into

the bayonet socket and secure

connection by tightening the

upper nut

Advantage : The two working

positions allow horizontal and

vertical areas to be easily cleaned

(fig. L).

The Power Scrubbing

6.6 Terminating work (fig. M)

Brush must not be used

Attention! When using cleaning

rings, flush the unit thoroughly

with water after use to rinse

out the residual cleaning agent

as sediment will otherwise cause

interference with subsequent

operations:

1. Set the adjusting knob

of the dispens-

ing unit to

this position:

The dispensing function

is shut off and clear water

is delivered (fig. M 1).

2. Flush the unit for approx.

1 minute with clear water.

3. Turn the tool off (ON / OFF

switch to position 0, figure M 2).

4. Turn off the water supply

(fig. M 3).

of the high-

7. Trouble-shooting

Fault

Motor does not run

when switched on.

The Power Scrubbing Brush

does not build up sufficient

pressure.

Fluctuations in the working

pressure.

Pump leaks.

No cleaning agent dispensed.

5. Actuate the high-pressure gun

to lock the gun so as to pre-

using the operating lever

vent any accidental opening

until emptied of all water and

(fig. M 4).

is at ambient pressure, and

6. Unplug the mains connector

then press the safety button

plug from the outlet socket.

Possible causes

Remedy

Check that the voltage given on

the nameplate is consistent with

the mains voltage.

Connecting cable damaged.

Check the connecting cable

for damage.

Connector plug not plugged

Check the connector plugs and

in correctly.

cable, have the switch checked by

Intermittence in the power

an authorised GARDENA Service

supply.

agent.

Mixing unit adjust-

Mixing unit ad-

ment knob set

justment knob

to position:

in position:

Air in the system.

Run the pump without the

high-pressure hose until water

exits the high-pressure outlet

without any bubbles.

Then connect the high-pressure

hose again.

Sieve in the water connection

Unscrew the tap connector,

blocked.

take out the sieve and clean.

Insufficient water admitted.

Check the amount of water

being admitted.

Leaks / blockage in the inlet line.

Check all inlet lines for blockage

and leaks.

High-pressure nozzle blocked.

Clean the high-pressure nozzle

by removing any dirt in the

nozzle with a needles and flush

out with running water.

Pump draws in air.

Check the suction lines for leaks.

It is usual that the pump leaks

Please consult GARDENA

to a small degree.

Service if the leak is large.

Dispensing unit incorrectly set.

Open the dispensing unit by

setting the switch to the "MIX"

position.

No cleaning rings in the

Place cleaning rings in the

dispensing unit.

dispensing unit (see 6.3 for this).