Fujitsu fi-5000N Початок роботи - Сторінка 13
Переглянути онлайн або завантажити pdf Початок роботи для Сканер Fujitsu fi-5000N. Fujitsu fi-5000N 29 сторінок. Fujitsu fi-5000n: user guide
Також для Fujitsu fi-5000N: Технічні характеристики (2 сторінок)
Друкувати сторінку
3. Enter the Administrator PIN (the default setting
is "5000"), and press the [ENT] key.
4. Select "Configure Network", and press the
[ENT] (Enter) key.
The following network configuration screen appears.
Do you want to
use DHCP?
Use DHCP
Use Static IP
5. To obtain the IP address automatically from the
DHCP (Dynamic Host Configuration Protocol)
server, select "Use DHCP" and press the [ENT]
key.
To set the IP address manually, select "Use
Static IP" and press the [ENT] key.
If "Use DHCP" is selected: It is not necessary to
specify the IP address, subnet mask and default gate-
way. Go to step 9.
If "Use Static IP" is selected: The following net-
work configuration screen appears.
IP Address:
Certain DNS servers and DHCP serv-
ATTENTION
ers, which do not support DNS
update, may cause host name resolu-
tion problems when DHCP is speci-
fied in IP address settings with
fi-5000N.
If you experience such problems, con-
sult with your network administrator
and take one of the following mea-
sures for fi-5000N and PC:
For fi-5000N,
1. Change to DNS server and
DHCP server which support DNS
update.
2. Set the IP address lease time
longer in DHCP server settings.
3. Use static IP method.
For PC,
1. Change to DNS server and
DHCP server which support DNS
update.
2. Set the IP address lease time
longer in DHCP server settings
and register the PC name on the
DNS server.
3. Use static IP method.
6. Enter the IP address.
The currently configured IP address is displayed on
the entry field. To change, press the [ESC] key once
to clear the entry field. Press the [ENT] key after you
have entered the correct address.
7. Enter the subnet mask next.
The subnet mask currently configured is displayed on
the entry field. To change, press the [ESC] key once
to clear the entry field. Press the [ENT] key after you
have entered the correct value.
8. The default gateway settings screen appears
next.
The portion specified at the IP address and subnet
mask will be displayed. Enter the remaining portion
of the default gateway and press the [ENT] key.
9. Enter the DNS server addresses
(DNS1: Primary;
DNS2: Secondary)
The currently configured address is displayed on the
entry field. To change, press the [ESC] key once to
clear the entry field. Press the [ENT] key after you
have entered the correct value.
To skip this step, clear the currently displayed
address or enter "0.0.0.0" on the entry field.
If the default gateway is correct, the Speed/Duplex
(Auto Negotiation) settings screen appears.
Select Speed/Duplex
Auto Negotiation
100BASE-TX Full
100BASE-TX Half
10.Press the [ ] or [ ] key to select one from
among "Auto Negotiation", "100BASE-TX Full",
"100BASE-TX Half", "10BASE-TX Full" and
"10BASE-TX Half", and press the [ENT] key.
Usually "Auto Negotiation" is selected. The
following network settings confirmation screen
appears when you press the [ENT] key.
IP
:XXX.XXX.XXX
MASK:XXX.XXX.XXX
GW
:XXX.XXX.XXX
OK:[ENT]/NG:[ESC]
11.Confirm the contents of the settings.
To change the settings, press the [ESC] key until it
returns to the setting screen of the item to change,
and configure again.
fi-5000N Getting Started
5