Kohler SV810-840 Посібник користувача - Сторінка 6
Переглянути онлайн або завантажити pdf Посібник користувача для Двигун Kohler SV810-840. Kohler SV810-840 20 сторінок. Vertical crankshaft
Також для Kohler SV810-840: Посібник користувача (21 сторінок), Посібник користувача (21 сторінок)
Друкувати сторінку
Operating
instructions
Also read the operating instructions
of rite equipment this
engine powers.
Pre-Start Checklist
•
Check oil level. Add oil if low. Do not overfill.
•
Check fuel level. Add fuel if low.
•
Check cooling air intake areas and external
surfaces
of engine. Make sure they are clean and
unobstructed.
•
Check that the air cleaner components
and all
shrouds,
equipment
covers, and guards are in
place and securely fastened.
Check that any clutches
or transmissions
are
disengaged
or placed in neutral.
This is especially
important
on equipment
with hydrostatic
drive.
The shift lever must be exactly in neutral
to
prevent
resistance
which could keep the engine
from starting.
WARNING:
Lethal Exhaust
Gases!
Engine exhaust gases contain poisonous carbon monoxide.
Carbon monoxide is odorless, colorless, and can cause death
if inhaled. Avoid inhaling exhaust fumes, and never run the
engine in a closed building or confined area.
Cold Weather
Starting
Hints
1. Be sure to use the proper
oil for the temperature
expected.
See Figure 2 on page 4.
2. Declutch
all possible
external loads.
3. Be sure tile battery is in good condition.
A warm
battery has much more starting capacity than a
cold battery.
4. Use fresh winter grade fuel. NOTE: Winter grade
gasoline has higher volatility
to improve
starting.
Do not use gasoline left over from summer.
Starting
1. Place the throttle control midway
between
the
slow and fast positions.
Place the choke control
into the on position.
2. Start the engine by activating
the key switch.
Release the switch as soon as the engine starts.
NOTE:
Do not crank the engine continuously
for
more than 10 seconds
at a time. If the engine
does not start, allow a 60 second cool clown
period between
starting attempts.
Failure
to follow these guidelines
can burn out the
starter motor.
NOTE:
If the engine develops
sufficient
speed to
disengage
the starter but does not keep
running
(a false start), engine rotation
must
be allowed
to come to a complete
stop before
attempting
to restart the engine.
If the starter is engaged
while the flywheel
is rotating,
the starter pinion and flywheel
ring gear may clash,
resulting
in damage
to the starter.
If the starter does not turn the engine over, shut off
starter immediately.
Do not make further
attempts
to
start the engine until the condition
is corrected.
Do
not jump start using another
battery (refer to Battery).
See your Kohler Engine Service Dealer for service
assistance.
3. For a Cold Engine - Gradually
return tile choke
control to the off position
after the engine starts
and warms up.
The engine/equipment
may be operated
during
the warm-up
period, but it may be necessary
to leave the choke partially
on until the engine
warms up.
4. For a Warm Engine - Return choke to off position
as soon as engine starts.
Stopping
1. Remove the load by disengaging
all PTO driven
attachments.
2.
For Engines
without
a Shutdown
Solenoid:
Move tile throttle to the slow or low idle position.
Allow the engine to run at idle for 30-60 seconds;
then stop the engine.
For Engines
Equipped
with a Shutdown
Solenoid:
Position the throttle control between
half and full throttle; then stop the engine.
Battery
A 12 volt battery is normally
used. Refer to the
operating
instructions
of tile equipment
this engine
powers for specific battery requirements.
If the battery charge is not sufficient to crank the
engine, recharge the battery.
Operating
Angle of Operation
This engine will operate continuously
at angles up to
25 ° . Check oil level to assure crankcase
oil level is at
tile FULL or "F" mark on tile dipstick.