aquasant AF1SL B0 R1 Посібник із швидкого старту - Сторінка 9

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Аксесуари aquasant AF1SL B0 R1. aquasant AF1SL B0 R1 16 сторінок. Hazardous fluid sensor

Друкувати сторінку

Assembly instructions

When mounting control units, sensors or probes, the relevant regulations and rules of Aquasant Messtech-

nik AG, SEV, the technical regulations for fill level monitors, SUVA, KVU, as well as the EMC directives must

be observed.

The place of installation of Aquasant monitoring systems must be reported to Aquasant Messtechnik AG or

to a licensed company, as well as to the responsible department.

The type of probe and control unit must match and correspond to the application (product-related applica-

tion, ex zone, lightning protection, etc.). During the commissioning and servicing of the system, its function

must be checked with original liquid (or non-hazardous replacement liquid).

The system must be checked or approved in accordance with the regulations of the TTV, SEV, etc. Special

level switches every 3 years / leakage monitoring every 2 years by Aquasant Messtechnik AG or a licensed

company.

In case of product changes, functional capability must be clarified with Aquasant Messtechnik AG or the

system functions must be checked.

The connected values of the power feed must be strictly observed, as shown in the technical data or wiring

diagram. In case of faults in the mains supply, a mains filter or mains stabilizer is recommended.

It is important to ensure that the air can circulate freely around the devices. It is advisable to leave an air gap

of at least 2 cm or more around the individual devices. This prevents a possible heat build-up.

For cabinet installation, the sensor connection cables must be routed separately and at a distance. Intrinsi-

cally safe sensor circuits (blue) must be distanced according to regulations by a thread length of at least 3

cm.

The control unit relay outputs are galvanically isolated and currentless. The currentless state or alarm status

is the same. (relay de-energized). In operation, without alarm, the relays are in the actuated state (self-

monitoring).

In order to prevent faults from short-term power failures, Aquasant

control units may need to be connected

to an accumulator or UPS.

All cables must be mounted according to the regulations of the KVU, SEV, SUVA and Aquasant Messtech-

nik AG, etc. The cables have to be mounted with bend protection as well as with a strain relief.

The sensor connection cables must be neatly disconnected and laid at a distance from high voltage and

high frequency cables. In intrinsically safe systems, the sensor connection cables must be coated in blue

(marking).

The cross-section of the sensor connection cables should be at least 0.75 mm

. If the probe or sensor con-

nection cables cannot be neatly disconnected and routed at a distance from high voltage current and high

frequency cables, shielded cables must be used. The shielding should be woven and only grounded on the

cabinet or device side.

The permissible line length is 1000 meters. The Aquasant cable type LiYY 3 x 0.75 mm

is subject to the

following parameters: R' = 50O/km; L' = 1mH/km; C' = 200 nF/km

Sensor connection cables must, whenever possible, be routed via a suitable, sealed connection box with

screw fitting (max. 5 m from probe or sensor). It must be possible to check the probe or sensor. When strip-

ping the coating, care must be taken that the insulation of the individual wires or strands is not damaged

(risk of short-circuit).

If the cables are routed via junction boxes, a wiring diagram must then be drawn up. A suitable, approved

sealed outlet with screw fittings must be used.

Operating manual on the Web or via QR code scan :

https://doc.aquasant.com/manuals/VEB-AFx_ATEX16_V19-8.pdf