Axon Body 3 Загальні вказівки

Переглянути онлайн або завантажити pdf Загальні вказівки для Камера спостереження Axon Body 3. Axon Body 3 2 сторінки. Camera battery replacement
Також для Axon Body 3: Посібник з експлуатації (2 сторінок), Посібник із заміни (7 сторінок)

Друкувати сторінку

Axon Body 3 Dock General Instructions

IMPORTANT: Before using an Axon Body 3 camera, ensure it is registered to your agency, assigned, and fully charged.

Refer to the Axon Body 3 Registration Guide or

Read, understand, and follow all warnings and instructions before using this product. The most up-to-date warnings and

instructions are available at www.axon.com.

Introduction

The Axon Body 3 Dock provides a network connection

for Axon Body 3 cameras to Axon Evidence.com or

Axon Commander, so the cameras can upload evidence

and download camera updates. While information is

securely transferred to your organization's account,

the dock also recharges the camera's battery.

The Axon Body 3 Dock only functions as an Ethernet

adapter, an unmanaged network switch, and charger.

This allows any Axon Body 3 camera to be docked in any

Axon Body 3 Dock, and still connect to the registered

agency's Axon Evidence.com or Axon Commander

account to upload video.

There are two types of Axon Body 3 Docks, a 1-Bay and

an 8-Bay version.

Go to

help.axon.com

for instructions, videos, and to

download the Axon Body 3 Dock Installation Manual.

Axon Body 3 Cameras and

Network Infrastructure

The network requirements for Axon Body 3 cameras

are provided below:

Note: If you are moving from previous generation

Axon body-worn cameras to Axon Body 3 cameras,

you may be required to make changes to your network

infrastructure. If your agency has concerns or questions

about any of the network considerations, please

contact your Axon representative in advance of your

deployment so that they can address these issues as

early as possible.

For more information, see the Axon Body 3 Dock

Installation Manual.

• Each Axon Body 3 camera requires its own IP address

when docked. The Axon Body 3 Dock itself has no

IP address, but each bay has its own Media Access

Control (MAC) address. The list of MAC address for

each bay is shown on the end of each dock.

• Static IP addresses are not supported. Dynamic Host

Configuration Protocol (DHCP) should be used to

provision the IP address and network settings. Each

Axon Body 3 Dock bay functions as an Ethernet card,

with its own MAC address.

• Upload bandwidth restrictions cannot be set for an

Axon Body 3 Dock.

• Axon Body 3 cameras require direct access to Axon

Evidence or Axon Commander through an Axon Body

3 Dock and do not support using a proxy server.

online instructions

for more information.

Axon Body 3 Dock Setup

The general steps for assembling, configuring, and

registering the Axon Body 3 Dock are provided below.

For detailed information on assembling, configuring,

and registering the Axon Body 3 Dock, go to

axon.com

the Axon Body 3 Dock Installation Manual.

Remove the Axon Body 3 Dock from the box.

Connect the Axon Body 3 Dock to the network

using WAN port.

Connect the Axon Body 3 Dock to power.

Device Manager (ADM). This is an optional, but

highly recommended step.

Axon Body 3 Camera

Registration

Prior to using an Axon Body 3 camera it must be

registered to your agency. Camera registration requires

the use of Axon Device Manager (ADM) and an Axon

Body 3 Dock. The general steps are provided below. For

detailed information on this process, go to Axon Body

3 section of help.axon.com.

Power on and place the unregistered Axon Body

3 camera in a powered and Internet connected

dock. Multiple cameras can be registered at the

same time, but each camera requires its own

dock bay.

Devices, and select Axon Body 3.

Follow the ADM on-screen instructions to

complete the registration process.

for instructions, videos, and to download

A 1-Bay Axon Body 3 Dock with an

Axon Body 3 camera.

An 8-Bay Axon Body 3 Dock

for Axon Body 3 cameras.

help.

Page 1