Sharp MX 5500N - Color Laser - Copier Посібник з усунення несправностей - Сторінка 38
Переглянути онлайн або завантажити pdf Посібник з усунення несправностей для Принтер "Все в одному Sharp MX 5500N - Color Laser - Copier. Sharp MX 5500N - Color Laser - Copier 48 сторінок. Digital full colour multifunctional system
Також для Sharp MX 5500N - Color Laser - Copier: Брошура та технічні характеристики (12 сторінок), Інструкція з використання Посібник з використання (14 сторінок), Посібник (49 сторінок), Посібник з техніки безпеки (28 сторінок)
Друкувати сторінку
Problem
The operation panel
cannot be used.
Printing is not
possible or stops
during a job.
The original size is not
automatically selected
or the wrong size is
selected.
The displayed bypass
tray paper size is not
correct.
36
Point to check
Does the message "Call for service.
Code:xx-xx*." appear in the touch
panel?
*Letters and numbers appear in xx-xx.
Is a tray out of paper?
Is the machine out of toner?
Has a paper misfeed occurred?
Is the output tray full?
Is the waste toner box full?
In the Paper Tray Settings of the system
settings, are restrictions placed on the
trays that can be used in each mode
(copy, print, fax, Internet fax, and
document filing)?
Is the original curled or folded?
Did you place an original smaller than
A5 (5-1/2" x 8-1/2") size?
Is the bypass tray extension pulled out?
Solution
Make sure that the LINE indicator is not lit and that the
DATA indicator is not blinking or lit and then switch off the
[POWER] key (
) and the main power switch. Wait at
least 10 seconds and then switch the main power switch
and the [POWER] key (
☞
Illustration of the machine (A) and (E) (page 44)
If the message still appears after switching the
[POWER] key (
) and main power switch off and on
several times, it is likely that a failure has occurred that
requires service. In this event, stop using the machine,
unplug the power plug, and contact your dealer or
nearest authorised service representative. (When
contacting your dealer or nearest authorised service
representative, inform them of the displayed error code.)
Add paper as instructed by the message in the touch
panel.
When toner runs low, a message will appear to inform
you that the toner cartridge must be replaced. To
replace the toner cartridge, see "5. MAINTENANCE" in
the User's Guide.
Remove the misfeed as instructed by the message in
the touch panel.
☞
REMOVING MISFEEDS (page 3)
When the output tray becomes full, a detector activates
and stops printing.
Remove the output from the tray and resume printing.
☞
Illustration of the machine (B), (C), and (D) (page 44)
Replace the waste toner box as instructed by the
message in the touch panel.
☞
"5. MAINTENANCE" in the User's Guide
Check the Paper Tray Settings and see if checkmarks
appear in the checkboxes of each mode (Feeding
Approved Job). Functions without a checkmark cannot
be used for printing using that tray.
➞ System Settings > "Paper Tray Settings" > "Tray
Settings" > "Change" >
The correct original size cannot be detected if the
original is curled or folded. Straighten the original.
Original sizes smaller than A5 (5-1/2" x 8-1/2") cannot
be detected. Enter the original size manually.
* When scanning a small original on the document
glass, it is convenient to place a blank sheet of paper
on top of the original which is the same size (A4
(8-1/2" x 11"), B5 (8-1/2" x 11"R), etc.) as the paper
that you wish to use for printing.
When loading paper in the bypass tray, be sure to pull
out the extension to enable the paper size to be
detected correctly.
☞
Illustration of the machine (H) (page 44)
) back on in that order.
(Each mode)