Cisco AIR-AP1010 - 1000 Series Lightweight Access Point Посібник із швидкого старту - Сторінка 16
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Бездротова точка доступу Cisco AIR-AP1010 - 1000 Series Lightweight Access Point. Cisco AIR-AP1010 - 1000 Series Lightweight Access Point 36 сторінок. Aironet 1000 series ieee 802.11a/b/g lightweight access points with internal antennas
Друкувати сторінку
Pre-Installation Configuration
Configuration Steps for an AP prior to installation
Step 1
Configure the Cisco Wireless LAN Controller in LWAPP Layer 3 Mode and be sure its DS Port is
connected to the network. Use CLI, Web User Interface or Cisco WCS procedures as described in the
appropriate Cisco Wireless LAN Controller Guide.
a.
b.
Step 2
Take the AP out of the box and plug it into the same subnet as the Cisco Wireless LAN Controller.
Step 3
Apply power to the AP:
a.
Note
These APs support 802.3af Power over Ethernet (PoE). These access points do not support Cisco
prestandard PoE. Please use Cisco 802.3af capable PoE switches or power injectors.
b.
c.
d.
e.
Step 4
After the Operating System code download is successful, the AP reboots. The GREEN LED turns on and
the two YELLOW LEDs indicate the states of the 802.11a and 802.11b/g networks. If any part of the
network is disabled in the Cisco Wireless LAN Controller, the corresponding YELLOW LED remains
off.
•
•
•
AP1010 Cisco Aironet 1000 Series IEEE 802.11a/b/g Lightweight Access Points with Internal
4
Be sure AP ports are available through the Cisco Wireless LAN Controller
Management/AP-Manager Interface.
Set the Cisco Wireless LAN Controller as the Master so that new AP always associate with it.
Use 802.3af-compatible PoE from an orderable inline power injector. If you do not have PoE
available, use an orderable AC-to-48 VDC External Power Supply plugged into the side of the AP.
After you power up the AP, the RED Alarm LED comes on for about 15-20 seconds and then all the
LEDs blink sequentially back and forth, indicating that the AP is trying to find a Cisco Wireless
LAN Controller to associate with. This can continue for up to five minutes. If the AP remains in this
mode for more than five minutes, the AP is unable to find the Master Cisco Wireless LAN
Controller. Check the connection between the AP and the Cisco Wireless LAN Controller and be
sure the AP and the Cisco Wireless LAN Controller are on the same subnet.
If the power light does not come on, check the power (it can be powered either with PoE or from an
orderable AP External Power Supply.
Be sure that a DHCP server is configured in the Cisco Wireless LAN Controller for both the
Management Interface and AP-Manager Interface using the CLI, Web User Interface, or Cisco WCS
interface, and that the DHCP server is operating correctly.
After the AP finds the Cisco Wireless LAN Controller, it attempts to download the new Operating
System code if the AP code version differs from the Cisco Wireless LAN Controller code version.
While this is happening, the LEDs on the top of the AP blink simultaneously.
Note that the Red LED can light for about 10-20 seconds when the AP reboots. If the RED LED
comes on AND STAYS ON for more than a minute, disconnect the Cisco Aironet 1000 Series
lightweight access point and call Cisco Technical Assistance Center (TAC).
From the CLI, Web User Interface or Cisco WCS interface, configure the AP with its Primary,
Secondary, and Tertiary Cisco Wireless LAN Controller names.
If required, use the CLI, Web User Interface or Cisco WCS interface to customize the AP-specific
802.11a, 802.11b and 802.11g network settings. Once again, the two YELLOW LEDs indicate the
states of the 802.11a and 802.11b/g networks. If any part of the network is disabled, the
corresponding YELLOW LED remains off.
Installation and Configuration
7817146-01