Cisco TelePresence Посібник з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник з монтажу для Сервер Cisco TelePresence. Cisco TelePresence 4 сторінки. Configuring a cisco unified communications manager sip trunk with a cisco telepresence content server
Також для Cisco TelePresence: Брошура (4 сторінок), Технічні характеристики (7 сторінок), Посібник адміністратора (27 сторінок), Короткий довідник (2 сторінок), Посібник (24 сторінок), Інструкція з монтажу (2 сторінок)

Друкувати сторінку

Installing Cisco TelePresence System Profile 65"

Mounting the wall stand

(applies to wall stand option only)

Long wall bracket

The wall brackets, bracket spacer, and Allen key

are found in the foot module box.

Short wall bracket

WARNING

Due to the size and mass of this equipment,

it is very important that the wall stand is

safely installed according to the installation

instructions, and that the wall is able to safely

support the product.

It is highly recommended that the wall stand is

installed by trained personnel.

Choose the short or long bracket depending

on the required distance between the

bottom module and the wall.

Place the spacer underneath the wall

bracket and fasten the bracket to the bottom

module. Re-use the existing three screws.

Use the Allen key, found in the foot module

box.

Place the bottom module by the wall, mark

where to fasten the bracket and move away

the bottom module.

Add the suitable fixing device for the screws

in the wall.

Connect the the cables (see step 11) and

lead them out at the back before fastening

the unit to the wall.

Place the bottom module by the wall and

fasten it to the wall.

Mounting the camera

RJ45

Open the top cover on

RJ45

HDMI

the monitor.

Connect the camera

cable to the HDMI and

RJ45 connectors on the

Mounting hole (Tripod) 1/4" UNC

camera.

S/N

Rev

Set the camera DIP switch (country specific setting):

• 50 Hz: 00011, gives 1080p50 (720p50 for HD-SDI).

• 60 Hz: 00100, gives 1080p60 (720p60 for HD-SDI).

Hold the camera

upside down and

carefully slide the

camera into place.

Choose the short or long bracket

depending on the required distance

between the bottom module and the

wall.

Spacer

Use the spacer between the bottom

module and the wall bracket.

Connect camera cables to the codec

Push the camera cable down the channel through the monitor.

Use the two cable clamps to fasten the cable inside the bottom module.

HDMI

Connect the camera cables:

Connect the HDMI cable to the

Connect the 9 pin D-SUb cable

HDMI 1 input at the codec.

to the Camera control input at the

codec.

Unpacking the monitor box and mounting the monitor to the base

HEAvY

AND

BULKY

REQUIRES:

4 PEOPLE TO LIfT

CAUTION

NOTE:

Requires 4 people

and lifting straps to lift.

LIFTING STRAPS INCLUDED.

The lifting straps are found

in the box, together with the

monitor, ready for use.

NOTE:

The straps are not

fixed to the monitor. be careful

when lifting the monitor so the

straps do not slide during the

lifting operation.

Mounting the grilles in front and finishing up

Close the top cover.

Snap on the top grille.

Snap on the speaker grille.

Remove the plastic foil on the monitor frame.

Use the supplied cloth to clean up the system.

Push the camera cable down the

channel through the Monitor.

Use the cable clamps to fasten the cable

inside the Bottom Module

and connect to the codec.

Camera cable

Camera cable goes

inside the channel.

The codec is placed

inside the front door.

Page 2

Connecting the monitor cables

Locate the cables in the bottom module and connect them as described

in the illustration:

HDMI cable

9 pin D-SUb cable

15 pin D-SUb cable

Power cable

A 级声明 (A Class product declaration)

本产品为 A 级 ITE，在其使用说明，铭牌等显著位置中已包含如下内容的声明

(We declare here that the subject product is A class ITE product, and the

following statement is clearly marked in the user manual or nameplate):

EMC Class A declaration

警告

此为 A 级产品。在生活环境中，该产品可能会造成无线电干扰。在这种

情况下，可能需要用户对干扰采取切实可行的措施。

WARNING:

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be

required to take adequate measures.

Connect cables on the rear side

声明所在位置 (Position of the Declaration):

使用说明 User Manual



Locate and connect the cables

铭牌 Nameplate



which are lead out of the system

at the rear side:

• Ethernet cable

申请号 (Application No.)：

• PC cable

申请人 (Applicant):

• Microphone cables

型号

(Model Number)：

• Power cable

Follow the instructions in

the accompanying Touch 8"

installation guide to connect and

initialize the touch interface device.

签字/盖章 Signature/Stamp:

Ethernet cable

日期 Date:

PC cable

Power

cable

Microphone

cables

Connect the microphone cables to the

Microphone connectors on the codec.