Philips AZ 2045 Посібник - Сторінка 5

Переглянути онлайн або завантажити pdf Посібник для Стереосистема Philips AZ 2045. Philips AZ 2045 8 сторінок. Cd soundmachine
Також для Philips AZ 2045: Посібник користувача (9 сторінок), Посібник користувача (15 сторінок), Технічні характеристики (2 сторінок), Посібник користувача (12 сторінок), Посібник з експлуатації (34 сторінок), Посібник (10 сторінок), (Шведською) Посібник із сніданків (8 сторінок)

Друкувати сторінку

English

TOP AND FRONT PANELS

(See 1)

1SOURCE – selects CD/ TUNER / TAPE function

2y – power on/ off switch

3Display – shows the status of the set

4Cassette recorder keys

RECORD 0 – starts recording

PLAY 2 – starts playback

SEARCH 5/6 – fast winds/rewinds tape

STOP/OPEN 9/

– opens the cassette compartment

– stops the tape

PAUSE ; – pauses playback or recording

5BASS, MID, HIGH – EQ keys to adjust the bass,

mid & treble frequencies

6PROG

CD:

programmes tracks and reviews the

programme;

Tuner: programmes preset radio stations

Navigation controls

7∞, §

CD:

– searches back and forward within a

track;

– skips to the beginning of a current

track/ previous/ later track

Tuner: – tunes to radio stations (down, up).

82; – starts or pauses CD playback

99 – stops CD playback;

– erases a CD programme

0MODE – selects different play modes:

e.g.

(random) order

REPEAT

SHUFFLE

!PUSH TO OPEN – opens/closes the CD door

@VOLUME – to adjust volume level

#REMOTE SENSOR (for AZ2055 model only) –

infrared sensor for remote control

$PRESET DOWN/ UP (–, +) – selects a preset

tuner station (down, up)

%BAND – selects waveband

^DBB – (Dynamic Bass Boost) activates a more

vivid bass response

CONTROLS

BACK PANEL

&Telescopic aerial – improves FM reception

*Battery compartment – for 6 batteries,

type R-20, UM1 or D-cells

(p – 3.5 mm stereo headphone socket

Note: The speakers will be muted when

headphones are connected to the set.

)AC MAINS – inlet for mains lead

REMOTE CONTROL (for AZ2055 only)

1VOLUME 3,4 – adjusts volume level (up, down)

2SHUFFLE – plays all CD tracks in random order

32; – starts/ pauses CD playback

4SEARCH 5, 6 – searches backwards/ forwards

within a track

5PRESET +, – – selects a preset radio station

(up, down)

6TUNING ∞, § – tunes to tuner stations

(down, up)

79 – stops CD playback;

– erases a CD programme

8¡, ™ – skips to the beginning of a current track

previous/ subsequent track

9REPEAT – repeats a track /programme/ entire CD

CAUTION

Use of controls or adjustments or performance of

procedures other than herein may result in hazardous

radiation exposure or other unsafe operation.

IMPORTANT!

For users in the U.K.: please follow the instructions on

the upper righthand-side.

BASIC FUNCTIONS

MAINS SUPPLY

Whenever convenient, use the mains supply to

conserve battery life. Make sure you remove the

power plug from the set and wall socket before

inserting batteries.

Batteries (not included)

• Insert 6 batteries, type R-20, UM-1 or D-cells,

(preferably alkaline) with the correct polarity.

Remote control (for AZ2055 only /See A)

• Insert 2 batteries, type AAA, R03 or UM4

(preferably alkaline).

Incorrect use of batteries can cause electrolyte

leakage and will corrode the compartment or cause

the batteries to burst.

• Do not mix battery types: e.g. alkaline with carbon

zinc. Only use batteries of the same type for the

set.

• When inserting new batteries, do not try to mix old

batteries with the new ones.

• Batteries contain chemical substances, so

they should be disposed of properly.

Using AC Mains

1 Check if the mains supply, as shown on the type

plate located on the bottom of the set,

corresponds to your local mains supply. If it does

not, consult your dealer or service centre.

2 If your set is equipped with a voltage selector,

adjust the selector so that it matches with the

local mains.

3 Connect the mains lead to the wall socket.

4 To disconnect the mains supply, unplug the set

from the wall socket.

Auto-Standby mode

When a CD or tape has reached the end of playback

and remains in the stop position for more than

15 minutes, the set will switch off automatically to

save mains.

The type plate is located on the bottom of the

set.

BASIC FUNCTIONS

Switching on and off and selecting function

1 Press y on the set to switch on.

2 Press SOURCE once or more to select:

function.

TAPE

3 Press y to switch off the set.

Notes:

– To change from

function, or

TAPE

TUNER

when you are switching off the set: first, make

sure you press the tape STOP 9 key to end

playback and all the cassette keys are released.

– The tone, sound settings, tuner presets and the

volume level (up to a maximum volume level of 20)

will be retained in the set's memory.

Adjusting volume and sound

1 Adjust the volume with the VOLUME control.

™ Display shows the volume level and a number

from 0-32. (See 2)

2 Press DBB once or more to select dynamic bass

boost on or off.

™ Display: shows

when activated.

3 To adjust the bass, mid and treble tones, press and

hold + or – on the BASS, MID, HIGH keys until

you reach the desired level, –5 to +5

™ Display briefly shows

, or

BASS

MID

HIGH

level. (See 3)

Note: To prevent sound interference the bass control

options operate exclusively. You cannot combine the

bass from BASS with DBB

™ The display shows

or the

indicator is

automatically switched off to remind you if you

attempt to use both bass settings.

TUNER

and the