Yamaha AX-892 Посібник користувача - Сторінка 13
Переглянути онлайн або завантажити pdf Посібник користувача для Підсилювач Yamaha AX-892. Yamaha AX-892 24 сторінки. Natural sound stereo amplifier
Друкувати сторінку
AX-892
NATURAL SOUND STEREO AMPLIFIER AX-892
1
2
POWER
SPEAKERS
PHONES
A
3
ON
OFF
4
1
Remote control sensor
Receives signals from the remote control.
2
POWER switch
Press this switch to turn the power on and off. When the
power is on, the indicator will be illuminated.
*Standby mode <Except for U.S.A. and Canada models>
While the power is on, pressing the POWER key on the
remote control switches the unit to the standby mode. (In
this mode, the power indicator on the unit is half-
illuminated.)
3
PHONES jack
When you listen with headphones, connect the headphones
to the PHONES jack and set both SPEAKERS A and B
switches to OFF.
4
SPEAKERS switches
For the desired speaker system(s), set the switch(es) to
ON. When using only one speaker system, set the other
switch to OFF.
5
BASS control
Used to increase or decrease the low-frequency response
Selecting "0" produces a flat response.
6
TREBLE control
Used to increase or decrease the high-frequency response.
Selecting "0" produces a flat response.
0
0
0
1
1
1
1
1
ON
OFF
2
2
2
2
2
3
3
3
3
3
4
4
4
4
4
– 5
5 +
– 5
5 +
L 5
SUBSONIC
BASS
TREBLE
FILTER
BALANCE
B
5
6
7
8
PHONES
FLAT
TAPE 2
CD
1
1
TAPE 1
TUNER
(MD)
-30db
2
2
TAPE 2
PHONO
10
(MD)
3
3
9
AUX
AUX
4
4
8
5 R
5
7
6
LOUDNESS
REC OUT
9
0
7
SUBSONIC FILTER switch
Used to eliminate undesirable ultra-low-frequency signals
caused by turntable rumble or warped records without
losing sound quality.
8
BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for channel imbalance caused by
speaker location or listening room conditions
9
Continuously variable LOUDNESS control
Used to boost high and low-frequency ranges at low
volume
(Refer to page 18.)
.
0
REC OUT selector
This switch can be used to select a source and send its
signal directly to the REC OUT terminals on the rear panel,
independently of the setting of the INPUT selector. This
function allows you to record the selected source while
listening to another source.
A
INPUT selector
Selects an input source to listen to.
B
MUTING switch
Press this switch to temporarily reduce the volume. Press
again to cancel the MUTING function.
C
VOLUME control and indicator
Used to raise or lower the volume level.
D
PURE DIRECT switch
Press this switch (the indicator lights up) to listen to a
source in the purest possible sound. (Refer to page 19.)
E
CD DIRECT AMP switch
Press this switch (the indicator lights up) to listen in the
.
purest possible sound from your CD. (Refer to page 19.)
E
CD DIRECT AMP
PURE DIRECT
INPUT
VOLUME
16
20
12
CD
TAPE 1
TUNER
28
PHONO
40
60
0
-db
MUTING
ON
OFF
A
AX-592 and AX-892 only
AX-892 only
AX-592 and AX-892 only
D
8
C
4
2
B
.
13