Directed Security and Remote Start Посібник з монтажу - Сторінка 8

Переглянути онлайн або завантажити pdf Посібник з монтажу для Автосигналізація Directed Security and Remote Start. Directed Security and Remote Start 20 сторінок. Security and remote start

Друкувати сторінку

1. Wiring Diagram

Tach threshold On/Off

In most cases, this jumper can be left in the Off position. Some new vehicles use less than 12 volts in their ignition systems. The unit may have

trouble learning the tach signal in these vehicles. Changing the jumper to the On setting changes the trigger threshold of the digital tach circuit

so that it will work with these type vehicles.

Light flash (+) / (-) polarity

The jumper is used to determine the light flash output polarity. In the (+) position, the onboard relay is enabled and the unit outputs (+)12V on

the WHITE H1/11 wire. In the (-) position, the on-board relay is disabled. The White H1/11 wire will supply a 200mA (-) output suitable for

driving factory parking light relays.

Note:

For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light flash output. P/N 8617 or a

standard automotive SPDT relay must be used on the H1/11 light flash output harness wire.

Transmitter/receiver Learn Routine™

The system comes with transmitters that have been taught to the receiver. The receiver can store up to 4 different transmitter codes in memory.

Note:

When doing any programming with security features off, the horn function (feature menu 1

item 13) must be programmed as Siren function to get an audible confirmation from the unit.

If the learn routines have been programmed using the Bitwriter, they may have been locked. Before proceeding with reprogramming

the learn routines, they must be unlocked with the Bitwriter - this cannot be done manually with the control center button.

Note

The Bitwriter requires software v2.7. Bitwriters with date code of 6A or older require an IC upgrade (p/n 998M). Some Bitwrit-

ers with a date code of 6B do not require the IC upgrade, refer to Tech Tip # 1112 for more information.

The control center button, plugged into the blue port, is used for programming. There is a basic sequence to remember whenever programming

this unit: Door, Key, Choose, Transmit and Release.

Open a door.

Insert the key. Turn the ignition to the ON position. The heavy gauge pink wire must be connected.

Choose. Within 10 seconds, press and release the Control center button corresponding to the number of the desired function step listed

in the following table.

Once you have selected the function step, press the control center button once more and hold it. The LED flashes and the siren chirps to confirm

the selected functional step. Do not release the control center button.

Step

Auto Learn Standard Configuration (default)

The auto learn configuration will automatically set up the remote button configuration. Note: You cannot change the configuration

of the remote control buttons.

Delete remotes: This feature will erase all remotes from the memory of the system. This is useful in cases when a customer's remote

is lost or stolen. Note: Does not reset the programmed features of the system or reset the Virtual Tach setting.

Reset Features: This resets all the features of the system to the factory default settings. Note: Does not delete the remotes from the

system or reset the Virtual Tach setting.

Virtual Tach Reset: Deletes all previously learned values for Virtual Tach, and on the next remote start sequence the unit will begin

virtual tach initialization. Note: The "Zap" feature on the Bitwriter does not reset the Virtual tach setting.

Transmit. While holding the Control center button, press the

has been successfully programmed or the selected feature has been reset. It is not possible to teach a remote control button to the system

more than once.

Release. Once the code is learned, or the feature reset, the Control center button can be released.

You can advance from programming one step to another by releasing the Control center button and tapping it to advance steps and then

holding it.

If you want to program Step 3 after programming Step 1, release the Control center button, press it twice and release it to advance to Step

3. Then press it once more and hold it. The siren chirps three times and the LED flashes three times to confirm it is ready to receive the code

from the transmitter.

Learn Routine is exited if:

•

Door is closed.

Function

button on the remote control. The siren chirps to confirm that the code