Diversa WORXI32-P-N Посібник з монтажу

Переглянути онлайн або завантажити pdf Посібник з монтажу для Аксесуари Diversa WORXI32-P-N. Diversa WORXI32-P-N 2 сторінки. Occupancy & vacancy sensors - recessed ceiling, passive infrared (pir), 347vac

Друкувати сторінку

Installation Guide

PART NO.

FEATURES

• Commercial grade components for long term reliability

WORSI32-P-N

standard lens, PIR,

• Straightforward wiring for quick installation

347Vac, 2-pole,

photo sensor

• Factory configured for the most common applications

WORXI32-P-N

• DIP switches and dials for advanced functionality

extended range lens,

PIR, 347Vac, 2-pole,

• Photo Sensor for Natural Daylight control

photo sensor

Operation

Diversa 347Vac sensors draw control power directly from the lighting circuit they are intended to control. When in

operation the sensor will detect initial motion using Passive Infrared (PIR); once motion is detected, the internal

contact will close. Motion through PIR is used to maintain the occupied condition as long as occupants remain

within coverage range of Sensor.

DIP Switches

Manual Override Button

(Shown with cover

plate removed)

Time Delay Dial

Ranges from 30s to 30 min.

Full turn Clockwise for Auto Time

Full turn Counterclockwise for Test Mode

Photo Level Dial

Used to determine light

level for Photo Functions

SPECIFICATIONS

Power

• 347Vac

• 60Hz

Contact Ratings

• 347Vac - 800W

Power Consumption

• 5.7mA

Approvals

• Certified to UL 508, UL244A, CSA C22.2 #14

Environment

• Indoors, stationary, non-vibrating, non-corrosive atmosphere an

non-condensing humidity

• Ambient Operating Temperature: 32°F to 104°F (0°C to 40°C)

• Storage Temperature: -14°F to 140°F (-25°C to 60°C)

Diversa by Douglas Lighting Controls

Diversa Occupancy & Vacancy Sensors - Recessed Ceiling, Passive Infrared (PIR), 347Vac

Line Voltage Passive Infrared (PIR) Occupancy / Vacancy Sensor

Wiring

Instructions

Diversa 347Vac sensors include #14AWG wiring leads. Use appropriate sized wire nuts for connecting wires.

CAUTION: Turn power oﬀ at the circuit breaker before working on sensor. According to NEC 240-83(d), if the branch

circuit breaker is used as the main switch for a fluorescent lighting circuit, the circuit breaker should be marked SWD.

All installations should be in compliance with National Electric Code (NEC) and all state, provincial, federal, and local

codes.

Line

Neutral

Load

Sensor Location Guidelines

To optimize the performance of Diversa Sensors, please review the coverage pattern, range, and model to

match with the application. Room dynamics will change when people and furniture are occupying the space.

Test Mode LED

In some rooms, after move in, some sensors may require adjustments.

• Ensure that the sensor is at least 30 inches away from air handlers/registers and not pointed directly at

windows

• Check that you are installing the right product (check the product model number) as per the drawings

Auto Time LED

Sensor Location Guidelines for "P" models

• Place outside the direct cone of light from fixtures

• Between 3 to 12 feet from windows

• As close as possible to the fixture being controlled

• Above the least illuminated space in the work area

• Away from lighting that is not being controlled by the sensor

DIMENSIONS/MOUNTING

inches (mm)

Unit attaches to mounting ring with

•

screws or it can be mounted into an

octogan box.

Ceiling tile

0.88"

Mounting

Wire

(2 2 )

ring

2.0"

(52)

4.17"

3 0 ° Tilt

(106)

DIPs and Dials

under cover

plate

•

The WOR sensor will fit an octagon

box. It is very important that conduits

be attached at opposite ends of the

box.

Conduit

Octagon Box

• Use a 2 1/8 " or more, deep box.

If the box is less, use the spacer ring.

2-pole

No Neutral

Black

Blue

Black/White

Blue/White

Load

Switch

White

www.douglaslightingcontrols.com

Installation

Installing in Smaller Room (Standard Lens)

• Locate the sensor near the entrance door wall to prevent it from viewing out into the hallway.

• Positioning the sensor in this manner ensures that an occupant moves across the longest detection beam

upon entrance, utilizing the sensor's maximum PIR range.

• Optimal usage is to detect small motions such as hand movements

• Designed for a mounting height of 7-15 ft

Line

Neutral

Side View

9 ft

0 ft

Typical Enclosed O ce

Extended Lens for Larger Rooms

• Place the sensor near the center of the room ceiling. Locate it so the approximate distance of 27ft in

or in dead center of room.

• Tilt the lens to aim the detection zone to the bottom of the door.

• Positioning the sensor in this manner ensures that the beam does not reach outside the room without

reducing sensitivity.

• Optimal usage is to detect large motions such as walking.

• Designed for a mounting height of 7-15ft.

27ft

Side View

9 ft

0 ft

Typical Classroom

14040700-C

Top View

14 ft

7 ft

0 ft

7 ft

14 ft

14 '

12 ' 10 '

6 '

3 '

0 '

3 '

6 '

10 '

12 '

14 '

Top View

27 ft

14 ft

0 ft

14 ft

27 ft

27 '

16 '

9 '

3 '

0 '

9 '

16 '

27 '