CustomWorks Dominator Модель - Сторінка 8

Переглянути онлайн або завантажити pdf Модель для Іграшкова машинка на колесах CustomWorks Dominator. CustomWorks Dominator 17 сторінок. 1:10 scale 4wd dirt oval car kit

Друкувати сторінку

Bag I

cont...

3710

3634

5253

8122

1250

5292

5217

Bag J

Steering Assembly

-Parts for

Step#1

3646

Qty 1

Steering Post

-Parts for

Step#2

3642

Qty 1

Dom Radio Tray

8122

1233

5252

7207

STEP #2

8122

*MAKE RIGHT & LEFT ASSEMBLY*

- RIGHT ASSEMBLY SHOWN -

3634

1226

-NOTE: The fit of the assembly will be very tight to

align. Do NOT alter the parts to ease assembling

of this step. Steering pivot will be free however.

STEP #3

4244

3647

Qty 1

7207

Steering Pivot

Spacer

5240

Qty2

5242

Servo Mount

Large Servo Saver

STEP #1

3647

1233

3646

- Thread 8122 Ball Studs into the steering

arms, the LF in the middle hole, the RF in

the inner hole.

- Snap the steering arms from Bag "G"

8122

onto the steering arms and pivot.

3632

1226

- Slide (1) Thick 7047 Shim onto the axle and secure it

using (1) 7203 Roll Pin. The Roll Pin should be evenly

spaced in Axle.

- Press (1) 1250 O-Ring inside the Outdrive.

- Attach the Steering Assembly to the Suspension

Arm by passing (1) 4244 Susp Pin thru the parts

7203

using the 1255 Shims on both sides of the Castor

Block. Secure the pin using (1) 5292 Screw on each

side of the arm.

7047

THICK

- Fasten the 8122 Ball Stud to the Shock Tower in the

upper and outer most hole using (1) 5217 LockNut .

- Attach the Camber Link from Bag "G" by snapping

1255

the Ball Cups onto the Ball Studs.

Qty 1

1233

Qty 2

Flanged Bearing

Qty 1

5263

3209

Qty1

4-40 x 3/8 FH Screw

Antenna Mount

- Assemble the steering pivot as shown in

the diagram.

- Mount the steering assembly to

the chassis using (1) 5263 Screw

with Loctite on the threads.

- Press (1) 1226 Bearing into each side of the

3632 Steering Arm and insert the Front Axle

from Step 1.

- Insert (1) of each 3634 Steering Bushing into the

top and bottom of the 3710 Castor Block.

NOTE: Castor Blocks are RIGHT AND LEFT parts!

Blocks should lean toward rear of car!

-Carefully slide the dogbone thru the hole in the

Castor Block and align the Steering Arm between

the Steering Bushings. The fit of these parts are

tight and will ensure a good handling car.

-Fasten the assembly together using (1) 8122 Ball

Stud on the top and (1) 5253 on the bottom.

8122

Qty 6

5252

Ball Stud

4-40 x 1/4 BH Screw

1:1

Qty 3

5217

Qty 3

4-40 Lock Nut

MIDDLE HOLE

1:1

Qty 4

5263

Qty 1

4-40 x 3/8 FH Screw

1:1

5253

Qty 4

5212

Qty 4

4-40 x 3/8 FH Screw

Washer

INNER HOLE

5263