CustomWorks Dominator Модель - Сторінка 9

Переглянути онлайн або завантажити pdf Модель для Іграшкова машинка на колесах CustomWorks Dominator. CustomWorks Dominator 17 сторінок. 1:10 scale 4wd dirt oval car kit

Друкувати сторінку

Bag J

cont...

5217

5240

5263

5252

(TO SERVO MOUNTS)

Mount Bag

-Parts for

3015

INT Front Bumper

Mount

Bag

3657

Qty 2

Rear Bumper Mount

FRONT

- Slide the Post Collar onto the 3229 Short Body Post, use the Set

Screw to retain the Collar.

- Mount the (2) 3229 Short Body Posts to the rearward set of holes

on the 3015 Bumper using 5283 Screw.

- Attach and center the 3015 Bumper to the 1275 Front Clip using

5283 Screws and 5207 Nuts. The bumper is slotted to allow you to

adjust the body position easily.

- Mount the 1275 Front Clip to the Chassis using (1) 5283 Screw

and 5207 Nut along with (2) 5254 Screws and 5217 Nuts.

5254

5253

5263

STEP #2

3209

5242

5240

5263

5252

(TO 3209)

Qty1

3229

Short Body Post

3658

Qty 1

Dominator Rear Bumper

1274

5283

3657

3658

5254

Qty4

3229 Qty4

3229 Qty 4

Post Collar

Set Screw

1274

Qty 1

5253

Rear Body Mount

4-40 x 3/8 BH Screw

3229

COLLAR

3229

POST

REAR

-Attach the (2) 3657 Rear Bumper Mounts to the Drive Carriers using (4)

5253 Screws and (4) 5263 thru the chassis.

- Mount the 3658 Rear Bumper to the Mounts using (4) 5254 Screws.

- Fasten the 1274 Rear Body Mount to the top of the Bumper Mounts

using (2) 5254 Screws and (2) 5217 Nuts for added strength.

- Attach the (2) 3229 Short Body Posts to the 1274 Rear Body Mount using

5283 Screws.

- Side the Body Post Collars onto the Body Posts and use the 3229 Set

Screw to adjust the height of the collar for the body of your choice.

- Fasten the 3642 Radio Tray to the Main Chassis using

(3) 5263 Screws & (3) 5217 LockNuts.

- Attach 5240 Servo Mounts to your servo in the

position shown using 5253 Screws and 5212 Washers.

- Fasten the servo to the Radio Tray using (2) 5252

Screws.

- Thread 8122 Ball Stud into the lower-most center

hole in the 5242 Servo Saver.

- Determine which of the Spline Inserts are correct for

your servo by pressing it over the drive on the servo.

Align the servo so it has equal throw in both direc-

tions.

- Press the Servo Saver onto the Spline Insert so that

the Servo Saver is perpendicular to the servo, attach

using the screw that came with your servo.

- Snap the main steering link from "Bag G" on the

remaining 8122 Ball Studs.

- Attach the 3209 Antenna Mount using a 5263 Screw.

1:1

5283

Qty 7

1275

8-32 x 1/2 FH Screw

INT Front Clip

1:1

Qty 6

5263

Qty 6

4-40 x 3/8 FH Screw

3229

COLLAR

SET SCREW

3229

5207

POST

5283

3015

5207

Qty 3

Qty1

8-32 Lock Nut

1:1

5254

Qty 6

5217

Qty 4

4-40 x 1/2 BH Screw

4-40 Lock Nut

5207

5283

1275

5263