1010music Toolbox Посібник користувача - Сторінка 10

Переглянути онлайн або завантажити pdf Посібник користувача для Обладнання для запису 1010music Toolbox. 1010music Toolbox 16 сторінок.
Також для 1010music Toolbox: Посібник із швидкого старту (2 сторінок)

Друкувати сторінку

The MIDI signals are output through the MIDI Output Jacks on the right edge of the module. The Note Sequencer

parameters allow you to configure the MIDI port and channel for playback of each Note Sequencer. All Note

Sequencers could output to the same port and channel, or each could be routed to a different port or channel. The

MIDI output is polyphonic and can play up to 128 notes per step per port. When the sequence is recorded via MIDI

input, the MIDI output will include gate, pitch and velocity information. Notes that are placed manually via the

touchscreen will include only gate and pitch information in the MIDI output. The Note Sequencer is the only element

of toolbox that sends a signal to the MIDI output.

Follow these steps to create a Note Sequence:

From the Main screen, touch one of the Note Sequencers in column 3 to display

the Note Sequencer screen. The black and white display along the left side of the

screen represents notes on a keyboard, with higher pitched notes at the top of the

screen. The vertical gray bars represent steps in the sequence. Blue rectangles

represent notes in the sequence. MIDI output can support multiple notes per step,

but CV output only supports one note per step.

There are three ways to add notes to the sequence:

Touch the screen at the step and note position desired.

Touch Rec to record inputs coming in through the MIDI Input Jack in real

time. Touch Rec again to stop recording.

Touch Step to record inputs coming in through the MIDI Input Jack with

each successive MIDI input note adding a note to the next step in the sequence. Touch Step

again to stop recording.

You can use the Control Knobs and touch gestures to zoom and scroll through the sequencer:

Action

Turn the top left control knob

Turn the top right control knob

Turn the bottom left control knob

Turn the bottom right control knob

Two finger pinch or stretch

Single finger drag or swipe

Note:

When the Sequencer Screen reloads, it zooms horizontally to display the number of steps that have

•

been selected in Step Count, and scrolls vertically to display the entered notes.

The cursor position is restricted to the Step Count configured for this Note Sequencer.

•

When recording, the sequencer will add the incoming notes to the sequence. It will not remove

•

previously existing notes. Touch Clear before touching REC if you want to start with a clean piano

roll.

Press the INFO button to toggle the display between the Note Sequencer Screen and the Note Sequencer

Parameters screen pages 1 and 2.

Use the Control Knobs to adjust the values of the parameters:

Parameter

Description

Step Len

Controls the length of time the sequence

will spend on each step, in terms of

fractions of a bar. This parameter can be

modulated.

Duty Cycle

The duration of the note events where 0%

is inaudible, and 100.0% is always playing.

P. 10

11/23/17 10:32 AM

Result

Moves the current note position cursor

Scrolls the piano roll up and down

Zooms the piano roll in and out vertically only

Scrolls the piano roll left and right

Zooms the piano roll in the direction pinched or stretched

Scrolls the piano roll

Range of Values

1/64, 1/32T, 1/32, 1/16T,

1/16, 1/8T, 1/8, 1/4T, ¼,

1/2T, ½, 1 bar, 2 bars, 4

bars, 8 bars

(T= Triplet)

0% to 100.0%

Digital Heart – Analog Soul

Toolbox User Manual

Figure 1 0: Note

Sequencer Sc reen

Figure 1 1: Note

Sequencer P a ra meters

P age 1