1010music Toolbox Manuel de l'utilisateur - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} 1010music Toolbox. 1010music Toolbox 16 pages.
Également pour 1010music Toolbox : Manuel de démarrage rapide (2 pages)
Imprimer la page
The MIDI signals are output through the MIDI Output Jacks on the right edge of the module. The Note Sequencer
parameters allow you to configure the MIDI port and channel for playback of each Note Sequencer. All Note
Sequencers could output to the same port and channel, or each could be routed to a different port or channel. The
MIDI output is polyphonic and can play up to 128 notes per step per port. When the sequence is recorded via MIDI
input, the MIDI output will include gate, pitch and velocity information. Notes that are placed manually via the
touchscreen will include only gate and pitch information in the MIDI output. The Note Sequencer is the only element
of toolbox that sends a signal to the MIDI output.
Follow these steps to create a Note Sequence:
1.
From the Main screen, touch one of the Note Sequencers in column 3 to display
the Note Sequencer screen. The black and white display along the left side of the
screen represents notes on a keyboard, with higher pitched notes at the top of the
screen. The vertical gray bars represent steps in the sequence. Blue rectangles
represent notes in the sequence. MIDI output can support multiple notes per step,
but CV output only supports one note per step.
2.
There are three ways to add notes to the sequence:
a.
Touch the screen at the step and note position desired.
b.
Touch Rec to record inputs coming in through the MIDI Input Jack in real
time. Touch Rec again to stop recording.
c.
Touch Step to record inputs coming in through the MIDI Input Jack with
each successive MIDI input note adding a note to the next step in the sequence. Touch Step
again to stop recording.
3.
You can use the Control Knobs and touch gestures to zoom and scroll through the sequencer:
Action
Turn the top left control knob
Turn the top right control knob
Turn the bottom left control knob
Turn the bottom right control knob
Two finger pinch or stretch
Single finger drag or swipe
Note:
When the Sequencer Screen reloads, it zooms horizontally to display the number of steps that have
•
been selected in Step Count, and scrolls vertically to display the entered notes.
The cursor position is restricted to the Step Count configured for this Note Sequencer.
•
When recording, the sequencer will add the incoming notes to the sequence. It will not remove
•
previously existing notes. Touch Clear before touching REC if you want to start with a clean piano
roll.
4.
Press the INFO button to toggle the display between the Note Sequencer Screen and the Note Sequencer
Parameters screen pages 1 and 2.
5.
Use the Control Knobs to adjust the values of the parameters:
Parameter
Description
Step Len
Controls the length of time the sequence
will spend on each step, in terms of
fractions of a bar. This parameter can be
modulated.
Duty Cycle
The duration of the note events where 0%
is inaudible, and 100.0% is always playing.
P. 10
11/23/17 10:32 AM
Result
Moves the current note position cursor
Scrolls the piano roll up and down
Zooms the piano roll in and out vertically only
Scrolls the piano roll left and right
Zooms the piano roll in the direction pinched or stretched
Scrolls the piano roll
Range of Values
1/64, 1/32T, 1/32, 1/16T,
1/16, 1/8T, 1/8, 1/4T, ¼,
1/2T, ½, 1 bar, 2 bars, 4
bars, 8 bars
(T= Triplet)
0% to 100.0%
Digital Heart – Analog Soul
Toolbox User Manual
Figure 1 0: Note
Sequencer Sc reen
Figure 1 1: Note
Sequencer P a ra meters
P age 1
Copyright 1010music LLC 2017