Cyrus 6vs Інструкція користувача - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкція користувача для Підсилювач Cyrus 6vs. Cyrus 6vs 7 сторінок.

Друкувати сторінку

User Instructions

Tape/Disc Playback and Recording

Playback: You can play back a recording by selecting the appropriate key

TAPE h. When TAPE is selected the indicator above the selected key will

light in addition to the selected source. To cancel TAPE, press the TAPE key

again. If the tape recorder has a three-head facility, selecting the TAPE key

will monitor the recording directly from the third head, whilst recording.

Recording: To record, select an input to record with the relevant Key h-s

and follow the recording instructions in your tape deck manual.

Volume and Balance

(Refer to fig 3)

The LEVEL CONTROL f of the Cyrus 6vs/8vs performs the dual functions of

volume and balance.

Volume: In normal mode the LEVEL CONTROL controls the volume in 1dB

steps. The light ring around the knob is calibrated to show the current

loudness level. When the volume is at minimum the first indicator on the light

ring will be RED. As the volume increases a GREEN light moves clockwise

around the ring. The volume setting is stored when the unit is set to standby.

Balance: Press the BALANCE control key on the remote control f to

change the mode of the front panel LEVEL CONTROL f to that of Left/Right

Balance. The light ring works in "reverse video" with the unlit section

indicating the position of L-R balance. You can alter L-R balance by up to +/-

4dB or switch one channel off when the control is turned to an extreme.

Mute

Pressing the MUTE Key a will fade the volume to minimum level without

disturbing the existing setting. When muted the RED minimum level indicator

will light as well as the existing GREEN light to show that the output is muted.

Move the volume knob up or press the Mute key to fade back up to the

original volume setting.

Listening to headphones

To listen to headphones, press the PHONES key d. The MUTE light at the

bottom of the light ring will now glow orange. The speakers will now be muted

for headphone listening. Press the PHONES key d again to restore

loudspeaker operation.

NOTE: The HEADPHONES key d only operates when headphones are

connected to the rear panel socket of the Cyrus 6vs/8vs.

Caution: If you have been listening to headphones at high volume, be sure to

turn the level down before you switch to normal loudspeaker operation.

Bi-amping / Tri-amping

The pre-amplifier output of the Cyrus 6vs/8vs may be used in conjunction with

added power amplifiers to upgrade your loudspeaker system through Bi-

amping or Tri-amping. The Cyrus range of power amplifiers is recommended

for this application.

Programmable Input Sensitivity

You may find an audible difference in level when switching from one input to

another due to the differing outputs of your source components. The unique

calibration memory of the Cyrus 6vs/8vs can be programmed to match the

sensitivity of all inputs with reference to the CD input. To program an offset:

Select CD input and set the volume control to a comfortable listening

level.

Select the desired input and hold the input key down. The volume

display switches to show input offset.

Adjust the level to the same audible volume as the CD player. The

display will read the offset applied.

Press the input key again to store this setting.

Repeat Steps 2 - 4 for each input to set the appropriate sensitivity level.

Fig. 5(a) - 5(c) shows settings for Input Sensitivity levels set -2 dB, 0dB and

+2dB relative to the CD input respectively.

(Refer to fig 4)

OPERATION WITH THE AVRS7 REMOTE CONTROL

The Cyrus 6vs/8vs is supplied with the Cyrus AVRS7 remote control which

will control Cyrus

players, tuners and surround sound decoders in addition

to the Cyrus 6vs/8vs.

System select keys

The AVRS7 will send commands to most products within the Cyrus range.

Commands may be sent to different system components by selecting the

appropriate system select key on the handset. These keys are marked CD,

TU, AV, AV-S and SETUP. The CD, TU, AV, AV-S keys flash to show which

type of product is under control. Commands to a surround decoder from the

SETUP system will flash the AV key.

•

Pressing CD will send commands to

also switch on the Cyrus 6vs/8vs and select the CD input of the

6vs/8vs.

•

Pressing TU will send commands to FM Tuners. This key will also

switch on an FM Tuner and select the TU input of the

•

Pressing AV will send commands to a DVD player. This key will also

switch on a DVD player and select the AV input of a

The Cyrus 6vs/8vs

will respond to the volume, balance, mute and input keys

when any of the above systems are selected.

NOTE - The AV-S and SETUP keys are not used to control a stereo system.

Multi-channel Surround Sound Systems

The AV-S and SETUP keys of the AVRS7 will control a Cyrus surround

decoder. If you own a Cyrus decoder which was not originally supplied with

an AVRS7 remote control, a full copy of the AVRS7 instruction sheet is

available on the Cyrus website www.cyrusaudio.com.

Full Remote Command Listing

A full listing of the command set available from the AVRS7 is listed in the

table overleaf.

Cyrus 6vs & Cyrus 8vs

a Cyrus CD

player. This key will

Cyrus

6vs/8vs.

Cyrus

6vs/8vs.

Cyrus