Electrolux # Benutzerhandbuch - Seite 8

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Staubsauger Electrolux # herunter. Electrolux # 9 Seiten. Over the range microwave oven
Auch für Electrolux #: Installationsanleitung Handbuch (8 seiten), Handbuch für Gebrauch und Pflege (20 seiten), Handbuch für Gebrauch und Pflege (36 seiten), Handbuch für Gebrauch und Pflege (24 seiten), Handbuch für Gebrauch und Pflege (38 seiten), Rezeptbuch (17 seiten), Gebrauchsanweisung (12 seiten), Handbuch für Gebrauch und Pflege (20 seiten), Gebrauchsanweisung (16 seiten), Gebrauchsanweisung (12 seiten), Insrtuktionshandbuch (16 seiten), Benutzerhandbuch (11 seiten), Handbuch für Gebrauch und Pflege (26 seiten), Handbuch für Gebrauch und Pflege (38 seiten), Handbuch für Gebrauch und Pflege (16 seiten), Handbuch für Gebrauch und Pflege (16 seiten), Installationsanleitung Handbuch (21 seiten), Benutzerhandbuch (16 seiten), Handbuch für Gebrauch und Pflege (16 seiten), Service-Handbuch (49 seiten)

Seite drucken
Electrolux # Benutzerhandbuch

Troubleshooting

For your safety, turn vacuum cleaner off and unplug power cord before attempting to resolve problems.
Problem
Motor will not start or
suddenly stops
No suction; vacuum cleaner does
not pick up lint or dirt.
Dust cup will not lock
Quick Release handle will not
lock into vacuum cleaner.
Brush roll will not turn.
Red 'check brush roll' or 'check
filter' indicator light is on.
6
Possible cause
Solution
Unit not connected to
n
power source.
n
n
Switch not turned on.
n
Thermal cut-off
n
has operated.
Blockage in hose.
n
Dust cup full.
n
Foam filter clogged.
n
Filter screen clogged
n
n
Foam filter not
n
in place.
n
Switch not on
n
proper setting.
n
Turbo nozzle clogged
n
Filter screen not in place.
n
Dusting brush and
n
telescopic wand are
extended.
n
Object caught in
n
brush roll.
n
n
Belt and/or brush roll not
n
positioned properly.
n
Brush roll not operating
n
properly or foam filter
is clogged.
Push plug securely into outlet.
Try another outlet and check circuit breaker.
Check plug and cord for damage.
Press power switch to 'carpet' or 'hard floor setting.
Correct the cause of motor overheating. See thermal
cut-off information page 1.
Remove any obstructions that restrict airflow through
hose. See page 5.
Empty dust cup. Make sure both chambers are
empty. See page 4.
Remove and clean foam filter. See page 4.
Fine dust can block airflow through the foam filter
and reduce suction, even if dust cup does not look
Remove and clean filter screen. See page 4.
Make sure filter screen stays in place inside dust cup
at all times.
Foam filter must be in filter frame for correct
performance. See page 4.
Make sure filter frame is installed properly in filter
cover for dust cup assembly to fit back into place.
See page 4.
Use 'carpet' setting for carpeted floors.
Use 'hard floor' setting for hard-surface floors and
when using accessories.
Remove and clean debris from turbo nozzle.
Locate filter screen and insert into dust cup.
See page 4.
Retract telescopic wand and dusting brush to expose
end of wand. See page 3.
Place end of wand into opening on back of vacuum
and align ribs into grooves. See page 2.
Remove the obstruction (such as carpet fringe,
string or sock). Note: brush roll overload protector will
reset when vacuum is turned off or unplugged.
Use 'hard floor' setting when vacuuming fringe
of rugs.
Check brush roll for threads and debris; clean if
needed. See page 5.
Make sure belt is on motor pulley and fitted into
grooves on brush roll. See page 5.
Make sure both ends of brush roll are free of debris
and secured properly so roll can rotate freely. See
page 5.
Check brush roll for threads and debris; clean if
needed. See page 5.