Siemens SINUMERIK 840D sl Upgrade-Anweisungen - Seite 3

Blättern Sie online oder laden Sie pdf Upgrade-Anweisungen für Industrielle Ausrüstung Siemens SINUMERIK 840D sl herunter. Siemens SINUMERIK 840D sl 3 Seiten. Operator panel front: op 010s
Auch für Siemens SINUMERIK 840D sl: Upgrade-Anweisungen (4 seiten), Upgrade-Anweisungen (5 seiten), Betriebshandbuch (33 seiten), Handbuch für die Inbetriebnahme (36 seiten), Upgrade-Anweisungen (3 seiten), System Manual (44 seiten), Handbuch Ausrüstung (28 seiten), Handbuch Ausrüstung (48 seiten), Handbuch Ausrüstung (26 seiten), Handbuch Ausrüstung (28 seiten)

Seite drucken

SINUMERIK 840D sl

System:

If, in conjunction with STEP7 on PCU 50, no communication is established between the HMI and the NCU,

•

please check the settings made under Control Panel / Set PG/PC Interface. In addition to S7ONLINE, an

Access Point

SINUMERIK_CP (SINUMERIK 7xx) -> TCP/IP -> VIA Rhine III Fast Eth. ..<Board 2>

must be included. If necessary, configure this Access Point as indicated.

Editor: The key combination Shift+Insert must be used to edit cycle calls directly in the DIN code. At present,

•

this is not provided on all SINUMERIK OPs. Remedy: Use an external PC keyboard.

To operate the simulation, the NC-MD $MC_FRAME_ACS_SET must be set to 1.

•

PCU 50.5 with OP019:

•

Copy a file station.ini with the following contents

[Metrics]

TCU_HWS_STMET_PANEL_OEM_LAYOUT = NORMAL

TCU_HWS_STMET_SOFTKEY_TYPE = 30

TCU_HWS_STMET_KEYBOARD_CAPS = 8

onto the NCU, into /card/user/common/tcu/<name_pcu50>/common/tcu and then execute the Linux

command sc distribute tcudata. Prerequisite: NCU has the entry "ON_MASTER" in

/card/user/system/etc/basesys.ini and has been booted with this entry.

To operate a PCU50 with external monitor, you can set the screen size of the Operate in the file

•

F:\hmisl\user\sinumerik\hmi\cfg\slrs.ini with the entry

[Global]

Resolution =

Variable view: The SK "Load symbols" has been removed from the screen "NC/PLC variables". The symbols

•

are automatically loaded as from SW 2.7 SP1. The symbol files are still stored in the directory

"/oem/sinumerik/plc/symbols".

Ctrl-Energy: Profiles with prewarning time 0 are not permissible and can no longer be generated by Operate.

•

The graphic view of tools can only be deactivated via the NC-MD 52271 TM_MAG_PLACE_DISTANCE by

•

setting the MD to 0mm.

ShopMill / ShopTurn:

•

The function "Block search upon selection / processing from the editor" should be deactivated via NC MD

51040.3 = 1 ($MNS_SWITCH_TO_MASCHINE_MASK Bit 3) because this may lead to a malfunction of the

operator interface.

•

Upgrade Instructions

SINUMERIK Operate 2.7 SP2 for PCU 50

; Permissible values: 640x480, 800x600, 1024x768, 1280x1024

2012-02-21

Page 3 of 3