Epson 1815p - PowerLite XGA LCD Projector Benutzerhandbuch - Seite 14

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Projektor Epson 1815p - PowerLite XGA LCD Projector herunter. Epson 1815p - PowerLite XGA LCD Projector 27 Seiten. Release of check tool for network projectors v1.00 for windows
Auch für Epson 1815p - PowerLite XGA LCD Projector: Benutzerhandbuch (42 seiten), Betriebshandbuch (36 seiten), Betriebshandbuch (47 seiten), Schnelles Einrichten (2 seiten), Benutzerhandbuch (1 seiten), Funktion Handbuch (5 seiten), Software-Handbuch (2 seiten), Konformitätserklärung (4 seiten), Teileliste (1 seiten), Produkt-Support-Bulletin (45 seiten), Produkt-Support-Bulletin (25 seiten), Produkt-Support-Bulletin (22 seiten), Produkt-Support-Bulletin (28 seiten), Produkt-Support-Bulletin (41 seiten), Produkt-Support-Bulletin (34 seiten), Produkt-Support-Bulletin (28 seiten), Produkt-Support-Bulletin (15 seiten), Produkt-Support-Bulletin (22 seiten)

Epson 1815p - PowerLite XGA LCD Projector Benutzerhandbuch
PowerLite 1810p/1815p
: Enter the IP address you want to assign to
IP address
the projector. It must be formatted like other addresses
on the network. The last octet should be unique.
: For example: 255.255.255.000, but this
Subnet mask
depends on how your network is set up.
: Enter the IP address that was
Gateway address
assigned to the access point or AirPort base station when
it was set up.
8. When you're done making these settings, select
, and then
Setup complete
save the changes. Press
Menu
Now you're ready to set up your computer for wireless
projecting. Go to "Configuring the Network Settings for
Windows" in the next section, or go to "Configuring the
Network Settings for Macintosh" on page 16.
Note: For specific details about your network, please consult your
network administrator. If you don't know your gateway or access
point address, see page 16. If you're using AirPort, start the AirPort
Admin utility, select your base station and click
click the
tab to see your base station's IP address.
Network
Configuring the Network Settings for Windows
Before connecting to the projector, you need to make sure the
settings for your computer's wireless card or adapter match the
settings you entered for the projector.
1. Access your wireless network Properties window. For
example, in Windows XP you would click
Panel > Network and Internet Connections
the
Network Connections
this:
Right-click and select Properties
14
PowerLite 1810p/1815p
-
Return
to confirm that you want to
Yes
to exit the menu system.
. Then
Configure
Start > Control
. Then click
icon. You see a screen similar to
2. Right-click the
select
Properties
,
3. Click the
Configure
4. Click the
Advanced
5. Check your wireless card's or adapter's device settings.
(Depending on the type of card or adapter you're using,
some of the settings may be different than those listed here.)
❏ Set the Network Type to
❏ Set the SSID to match the name assigned to the access
point (which should also match the projector's ESSID).
❏ Make sure Encryption is
encryption on the projector.
6. Click the
General
or adapter is enabled.
7. When you're done, click
dialog box.
3/08
Wireless Network Connection
. You see a screen similar to this:
button.
tab. You see a screen like this:
Infrastructure
if you have not set up
Disabled
tab and make sure that your wireless card
to close the wireless properties
OK
icon and
Click here
.