Fleetwood LI-Cocktail Benutzerhandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Blender Fleetwood LI-Cocktail herunter. Fleetwood LI-Cocktail 6 Seiten. Professional blender

Seite drucken

4.2.1 Danger

An electric cable or electric wire with damaged jacket or bad insulation

could cause electrical shocks as well as electrical leak. Before use, check conditions of

all wires and cables.

4.2.2 Advices

Be sure ALL INSTRUCTIONS in this manual have been thoroughly

understood. Every function and operational procedure have to be very clear to the

operator. Contact your nearest Dealer for further questions.

Any manual command (switch, button or lever) shall be given only

after being sure it is the correct one.

4.2.3 Precautions

The electric cable has to be compatible with the power required by the

machine. Cables touching the floor or close to the machine need to be protected

against short circuits.

Oil reservoir has to be full up to the required level as indicated. Check

4.3 Routine Inspection

4.3.1 Advice

When checking the tension of the belts or chains, DO NOT

introduce your fingers between the belts and the pulleys and nor between the chain

4.3.2 Precautions

Check if motors and sliding or turning parts of the machine produce

abnormal noises.

Check the tension of the belts and chains and replace the set when

belt or chain show signs of being worn out.

When checking tensions of belts or chain DO NOT introduce your

fingers between belts and pulleys, nor between the chains and gears.

Check protections and safety devices to make sure they are working properly.

4.4 Operation

4.4.1 Advice

Be sure your hair is not loose in order to avoid getting caught by turning

parts which could lead to a serious accident. Tie your hair well up and/or cover your

head with a scarf.

The operation performed by not trained or skilled personnel shall be

forbidden.

Never touch turning parts with your hands or in any other way.

NEVER operate machine without all original safety devices under perfect

2.2 What to do and what not to do with your Professional Blender

You have to:

2.2.1 – The voltage must be the same as the one specified on the

motor housing of the blender.

2.2.2 – The supporting surface must be clean and dry to avoid

strange substances or water within the motor.

2.2.3 – Put liquid ingredients inside the cup first, then put the solid

ingredients, unless the receipt tells you otherwise.

2.3.4 – Cut all fruits, vegetables, meat, fish and any other hard

ingredient in pieces of up to 2 cm. Cut cheese in pieces of up to 1,5 cm.

2.2.5 – Use a rubber spatula to push ingredients inside liquids

ONLY with the machine turned off.

2.2.6 – Place the lid firmly to the cup before turning the machine on

and keep your hand over the lid while machine is operating.

2.2.7 Remove sauces, butter, mayonnaise and similar consistent

products taking the cup off and pushing the product through the cup

lower open side.

You should not:

... expect your blender to replace any other kitchen appliance. It is not

supposed to make mashed potatoes, it does not blend egg white or any

other cream for covering, it does not grind raw meat, it does not blend

dough and not extract pulp from fruits and vegetables.

... process the mixtures for too long. Remember that the blender works in

seconds and not in minutes. Therefore, never let your blender working for

more than one minute. It is better to turn it off and check the mixture

consistency after a few seconds to avoid too much blending, then run the

motor again using the pulse function .

... overload the motor with too big or heavy portions as it will make the

blender´s life shorter. If motor stops, turn it off immediately, unplug and

remove part of the load before start operating again.

3 - OPERATION

3,1 – To start machine

Start machine by turning ON/OFF PULSE Switch No. 04 (Pic. 01) to

position ON, the Switch is located on the motor housing. Nº 01 (Pic. 01)