Galaxy Aqua 9000 XP Manual de instrucciones de instalación - Página 7

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Productos de fontanería Galaxy Aqua 9000 XP. Galaxy Aqua 9000 XP 11 páginas. Pumped instantaneous electric shower

Imprimir página

1. Plumbing Connections

CAUTION

Check there are no hidden cables or

pipes before drilling holes for wall plugs.

Exercise great care when using power

tools near water. The use of a residual

current device (RCD) is recommended.

1. Establish position for the

riser rail, and mark the wall for

the lower mounting bracket.

Make allowances for the tallest

person likely to use the shower

regularly.

2. Use a No 10/5.5mm masonry

drill to make a hole 35mm deep,

and fit the wall plug.

(NB some

wall constructions may require the

use of alternative types of wall

fixings).

Screw the lower bracket

base to the wall.

3. Locate the crimped end of

the riser rail (Figure 4) into the

mounting bracket, then fit the

upper bracket. Ensure the rail is

vertical, then mark the wall for

the fixing.

4. The crimped end of the riser

rail.

NOTE If it is necessary to

shorten the rail, use a junior

hacksaw to cut the excess material

from the plain end of the rail.

5. The three components that

comprise the Handset Height

Adjuster assembly are

produced with alphabetical 'A's

and 'B's moulded into the end

section of each part. Simply just

match the letter identification of each part with

the central piece i.e. 'A' to 'A' and 'B' to 'B' for

correct assembly.

6. With the showerhead height

adjuster lever set a 3 o'clock

and the showerhead holder in

the upright position, slide the

assembly onto the rail. Tighten

to the rail by turning the lever.

7. To lock the Handset Height

Adjuster at your chosen position

on the rail. Turn the lever up

right. This action is also used for

holding the showerhead at the

angle required.

8. Re-assemble the rail and

screw the upper mounting

bracket in place.

9. Slide the end cap onto the

mounting brackets.

10. Snap the soap dish onto the

rail below the holder assembly.

11. Slide soap dish down the

rail to required position.

12. Firmly attach flexible hose to

the showerhead making sure

sealing washer is in place.

NOTE the adjustable slider grips the

conical end of the hose, not the

handle of the showerhead.

Maintenance:

Clean regularly with a non-abrasive liquid

bathroom cleaner.

SECTION

OPERATING THE SHOWER

IMPORTANT: Ensure the commissioning

procedure has been carried out.

select a larger cable size.

23. In the majority of installations, the

cable will unavoidably be placed in

one or more of the above

conditions. This being so, it is

strongly recommended to use a

minimum of 10mm cabling

throughout the shower installation.

24. In any event, it is essential that

Individual site conditions are assessed

by a competent electrician in order to

Determine

SECTION

WATER REQUIREMENTS

The installation must be in accordance

with Water Regulations / Byelaws.

WARNING: Under no circumstances

must this Aqua 9000 XP pumped

shower be connected directly to the

mains water supply.

To ensure activation of the heating

elements, the shower must be connected

to a Cold water supply which is gravity fed

from a static Cold water storage cistern

with a minimum capacity of 114 litres

(25 galls).

There must be a maximum head of water

of 10 metres (33ft) and a minimum head

of 8 cm (3") as measured between the

Bottom of the cistern and the top of the

shower unit. There must be no other Cold

water draw offs between the cistern and

the unit and the pipe must not supply

water to any other tap or fitting at a lower

level.

NOTE: The supply pipe from the cistern

should be on the opposite side to the float

operated valve to prevent air being drawn

into the pipe when the cistern is filling.

If it is intended to operate the shower in

hard water areas (above 200 ppm

temporary hardness) a scale inhibitor

should be fitted.

Fig.2 shows a typical system layout. Do

not use jointing compounds on any pipe

fittings for the installation.

SECTION

SITING OF THE SHOWER

WARNING: The shower must not be

positioned where it will be subjected to

freezing conditions.

FOR EASE OF SERVICING, THE UNIT

MUST ALWAYS BE MOUNTED ON THE

SURFACE OF TILED WALLS. NEVER

TILE UP TO THE UNIT.

Refer to Fig.3 for correct siting of the

shower. This product is splash-proof rated

and is approved for use in shower

cubicles and over baths.

However, do not install the unit in a

Position where the sprayhead will

consistently direct water over it.

The shower unit MUST be positioned

vertically.

Fig.2