Conrad 43 75 54 Manuel d'utilisation - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Conrad 43 75 54. Conrad 43 75 54 8 pages. Led recessed light 2.7 w, set of 3

Imprimer la page

Preparing installation

Caution!

The LED transformer is outfitted with a fixed Euro power cable for easy connection

to the power supply.

Should you wish to remove the power cable in order to connect the LED transformer

directly to a screw terminal, please note that this procedure may be carried out by a

qualified electrician who is familiar with all applicable regulations only!

When handling mains voltage improperly, you will not only endanger yourself but

also others!

• Mount the product out of the reach of children.

• A stable surface is needed for installation.

• The product may not be operated until after installation.

• The product must be completely free of voltage for installation. Do not connect the LED

transformer to a power outlet until after the product is successfully installed and connected.

Installation and connection

In order to guarantee proper and safe installation, review all information in

the chapters "Explanations of symbols", "Safety instructions" and "Preparing

installation".

1. Choose an appropriate site for mounting. Make sure to observe the required minimum

safety clearance. When choosing an installation site, please also take into consideration

cable routing and the LED transformer.

2. Turn the decorative rings on the light housing counter clockwise and remove them.

3. Loosen the two screws that fasten the illuminant to the light housing and remove the

illuminants with their cables.

4. Use one of the three light housings as a template to mark the positions for drilling holes. You

will need one drilling hole per light housing.

5. Drill the holes in the mounting surface.

When drilling or tightening screws, make sure not to damage any cables, wires or

pipes located underneath the surface.

6. Insert wall anchors into the drilling holes and mount each light housing to a screw using

the metal tongue.

7. Fasten the illuminants in the light housings.

8. Replace the decorative rings and turn clockwise to fasten.

9. Connect the lights' reverse polarity protected plugs to the proper jacks on the cable harness.

The plugs should click into place. Do not use force.

10. You can secure the LED transformer in place using two screws (not included) if necessary.

11. Connect the LED transformer to a power outlet. The product is now operational.

Turning on/off

The on/off switch is located on the side of the light housing connected directly to the LED

transformer.

Troubleshooting

Problem

Possible cause

The power plug is not

connected to the outlet

correctly.

The lights' plugs are not

The LEDs do not light up.

connected to the cable

harness.

The circuit's fuse or residual

current device is not active.

Maintenance and cleaning

• Besides occasional cleaning, the device is maintenance-free.

• Remove dust using a clean, soft brush or vacuum cleaner. Or use a clean, soft and dry cloth.

Disposal

You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

a) General

Protection type ...........................IP20

Operating temperature ..............-20 to +85 ºC

Storage temperature ..................-35 to +85 ºC

Weight .......................................715 g

b) LED transformer

Input voltage ..............................220 – 240 V/AC, 50 Hz

Output voltage ...........................12 V/DC

Output current ............................1.25 A

Protection class .........................II

Power cord length ......................1.52 m

c) LED recessed lights

Illuminant ...................................15 SMD LEDs, non-dimmable

Power consumption ...................max. 2.7 W

Protection class .........................III

Luminous flux ............................230 lm

Color temperature ......................3000 K

Beam angle ...............................120º

Solution

Make sure that the power

plug is properly plugged in.

Make sure that the lights'

plugs are properly plugged

in.

Activate the circuit's fuse or

residual current device.

Never use any aggressive cleaning agents or chemical solutions to clean the lights.

Doing so may cause discoloration.

Electronic devices are recyclable waste and must not be disposed of in the household

waste.

At the end of its service life, dispose of the product according to the relevant statutory

regulations.

The information contained under point "c)" applies to one LED recessed light.

These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1,

D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,

or the capture in electronic data processing systems require the prior written approval by the editor.

Reprinting, also in part, is prohibited.

These operating instructions represent the technical status at the time of printing. Changes in

technology and equipment reserved.

V2_0813_02-HK