Automatic Technology Australia Securalift GDO 2v4 Instructions d'installation et manuel du propriétaire - Page 12
Parcourez en ligne ou téléchargez le pdf Instructions d'installation et manuel du propriétaire pour {nom_de_la_catégorie} Automatic Technology Australia Securalift GDO 2v4. Automatic Technology Australia Securalift GDO 2v4 19 pages.
Imprimer la page16.1
TO
INITIALISE
OBSTRUCTION
FORCE.
(a)
Press
and
hold the
close
button
'F",
move the
door to the
fully
closed position.
If
the door is al-
ready closed disregard step (a)
(b)
Press
the reset button for
two
seconds,
the door
should start opening. As soon
as
the door
reach's
the
fully
open
position
it will
pause
momentarily
and
than start to close on its own.
The door
has to
do a
full
open and close cycle
with
no
interrup-
tions
for
the
safety obstruction parameters to
be calculated and set automatically.
Do not
ob
struct the door during this procedure.
A
default safety force
pressure
margin is preset in
the
factory. Under normal operating
conditions
this
default margin should not be changed however
.-
yo,
are
unhappy
with the
pressure
you
can
change
it as
per
below.
16.2
TO DECREASE FORCE PRESSURE
(a)
Press
and hold the Force
Margin
Set
button'I'
see
FIG
16a.
(b)
While holding down button
'I'
press
the Close
button 'F'.
The red
LED
will
illuminate
each
time
the close button is pressed
to
indicate that the force
pressure
is
being
reduced.
When the red LED
flashes continuously when
the
close
button is
be-
ing
pressed
this
indicates that
the minimum force
pressure
setting has being reached. To increase the
force pressure go to the next
step.
16.3
TO INCREASE FORCE PRESSURE
(a)
Press and
hold the Force Margin
Set
Button
'
I
'
See
Fig
16b.
.*;
Wnte
holding down button
'I'
press
the green
open button
'G'.
The
green
LED
will
illuminate
each
time the
open button
is
pressed
to
indicate
that the force
pressure
is
being
increased.
If
the
green
LED
flashes continuously when
the
open
button
is
being
pressed
,this
indicates
that
the
maximum force
pressure
setting
has
been reached.
16.4
TO
RECALL FACTORY
SET FORCE
(a) While holding
down the Force
Margin
Set
But-
ton
'I'
press
the RESET button
'A'
for two
sec-
onds
see
Fig
16c.
(b)
Release
both
buttons.
The default
setting
should now
be
recalled.
IMPORTANT NOTE:
Whenever
the
limit
switches
are adjusted
the
safety obstruction force has
to
be re
initialised
,
because
the
door travel
distance
may
have
changed.
To
re-initialise
please follow
STEP
16.1
above.
Page
CAUT
1
EN
II]S
UNIT
]S
NIT
USER
STRVI(]tAELt
I
I
SC!NNICT
P!\/tR
SUFPLY
BtT!RT
Rt[4NV
]
NG
It]VE
R,
FIG
16a
OPEN
aAlT
I
UN
IHIS
I.]N]T
]S N!T U:tR
StRViCtAELt
I
1
SC!NNtCT
P!\i/[R
SUPTtY
BtT!Rt
RtM!V
1
NG
CIVtR
LIM]T
CLOSE
r-\
LIIUIT
:,i;;@
CAI-]T
I
!II
IHI:
UN]T
IS
\It]T
UStR:tIiV]'TABtt
D1SCENNTCT
Pl\/tR
SI.]PPLY
BTt!Rt
Rtlvl!V
I
NG
CIVIR
FIG
l6c
t
il',,
\
*,tqF,+rr
10